Curriculum
Course: SAAT (Tahsili)
Login

Curriculum

SAAT (Tahsili)

Mathematics · Unit 1: Logic and Geometry

0/25 Dr Dabour Hub Science Diagram and Course Material

Mathematics · Unit 7: Mathematics question bank with original diagrams

0/1 Dr Dabour Hub Science Diagram and Course Material

Mathematics · Mock exams and full tests

0/1 Dr Dabour Hub Science Diagram and Course Material

Physics · Mock exams and full tests

0/1 Dr Dabour Hub Science Diagram and Course Material

Chemistry · Unit 9: Chemistry question bank with original diagrams

0/1 Dr Dabour Hub Science Diagram and Course Material

Chemistry · Mock exams and full tests

0/1 Dr Dabour Hub Science Diagram and Course Material

Biology · Unit 1: Introduction to Biology and Classification

0/20 Dr Dabour Hub Science Diagram and Course Material
Text lesson

9.1 Introduction to Physics and Measurement

Overview of Introduction to Physics and Measurement. This topic is covered in 2 lessons: Physical quantities, units and dimensional analysis; Precision, measurement and graphing.

1Key ideas2Key ideas3Key ideas4Key ideas
Key ideas
Key ideas
1
Physics describes nature with measurable quantities. Every measurement has a number and a unit.
2
The SI base quantities used most are length (metre, m), mass (kilogram, kg), time (second, s), electric current (ampere, A) and temperature (kelvin, K).
3
Derived quantities are built from base quantities: speed (m/s), force (newton, N = kg·m/s2), energy (joule, J = N·m).
1 / 4Next ▶
Key ideas
1

4
2

Prefixes scale units by powers of ten: kilo (103), mega (106), centi (10−2), milli (10−3), micro (10−6), nano (10−9).
3

5
4

Accuracy is how close a measurement is to the accepted value

precision is how close repeated measurements are to each other.
5

6
6

The precision of an instrument is limited by its smallest division

the uncertainty is usually taken as half of that division.
◀ Previous2 / 4Next ▶
Key ideas
Key ideas
7
Significant figures are the digits known reliably plus one estimated digit. Zeros between non-zero digits and trailing zeros after a decimal point are significant

leading zeros are not.
8
When multiplying or dividing, give the answer to the least number of significant figures

when adding or subtracting, to the least number of decimal places.
◀ Previous3 / 4Next ▶
Reading a measurement: A graduated cylinder shown enlarged, with the meniscus between the 21 and 22 mL marks and the reading taken at the bottom of the curved surface.
Key ideas
◀ Previous4 / 4
1Lessons in this topic2Lessons in this topic
Lessons in this topic
1

Physical quantities, units and dimensional analysis
2

— Distinguish base and derived quantities, use SI units and prefixes, and check equations with dimensional analysis.
3

Precision, measurement and graphing
4

— Distinguish accuracy from precision, apply significant-figure rules, and interpret linear, quadratic and inverse graphs.
5

The SI base units include the mole

which is the unit for amount of substance.
6

To convert hours to seconds, multiply by 3600

to convert seconds to hours, divide by 3600.
1 / 2Next ▶
Lessons in this topic
1

Absolute zero is 0 K

which equals −273.15 °C.
2

To convert from degrees Celsius to kelvin, add 273.15

to convert from kelvin to Celsius, subtract 273.15.
3

Standard form writes a number as a × 10n

where a is at least 1 but less than 10.
4

A positive power of ten in standard form means a large number, and a negative power means a small number.
5

When rounding to a set number of significant figures, round up if the next digit is 5 or more.
6

In standard form, only the number before the × 10n part is rounded when limiting significant figures.
◀ Previous2 / 2
1Base quantity
Base quantity — a quantity defined independently, such as length or time
2Derived quantity
Derived quantity — a quantity formed by combining base quantities
3SI
SI — the international system of units
4Prefix
Prefix — a word part that multiplies a unit by a power of ten
5Accuracy
Accuracy — closeness to the true value
6Precision
Precision — closeness of repeated measurements to each other
7Significant figures
Significant figures — the meaningful digits in a measurement
8Independent variable
Independent variable — the variable the experimenter changes
Base and derived quantities
Quantity Type SI unit
Mass base kg
Time base s
Velocity derived m/s
Force derived N = kg·m/s2
1

Convert every value to SI units before substituting into a formula.
2

To change km/h to m/s divide by 3.6; to go back multiply by 3.6.
3

A set of readings can be precise without being accurate (for example, with a zero error).
4

Read the axis labels and units before interpreting a graph.
Accepted payment methods