Curriculum
Course: Edexcel A Level Physics 9PH0
Login

Curriculum

Edexcel A Level Physics 9PH0

2. Mechanics

0/43 Dr Dabour Hub Science Diagram and Course Material

3. Electric Circuits

0/41 Dr Dabour Hub Science Diagram and Course Material

5. Waves and Particle Nature of Light

0/76 Dr Dabour Hub Science Diagram and Course Material

7. Electric and Magnetic Fields

0/46 Dr Dabour Hub Science Diagram and Course Material

8. Nuclear and Particle Physics

0/29 Dr Dabour Hub Science Diagram and Course Material

9. Thermodynamics

0/27 Dr Dabour Hub Science Diagram and Course Material

13. Oscillations

0/23 Dr Dabour Hub Science Diagram and Course Material
Text lesson

4. Materials

Materials: Density, Fluids, Viscosity and Mechanical Properties of Solids — EDEXCEL A LEVEL PHYSICS 9PH0 notes: Calculate density, upthrust and viscous drag, and use Hooke’s law, stress-strain data and strain energy to describe how materials deform.

1Density and unit conversions2Density and unit conversions3Density and unit conversions4Density and unit conversions
Density and unit conversions
Density and unit conversions
Density is the mass per unit volume of an object: ρ = m ÷ V.
1 / 4Next ▶
Density and unit conversions
1

Objects made from low-density materials typically have a lower mass for the same volume

a balloon is less dense than a small bar of lead even though it occupies a larger volume,
2

and gases are less dense than solids.
3

The units depend on those chosen: g and cm
4

3
5

give g cm
6

−3
◀ Previous2 / 4Next ▶
Density and unit conversions
Density and unit conversions
kg and m
give kg m
.
Volume may not be given directly and must be calculated from the shape (for a cuboid length × width × height

for a cylinder πr
2
h

for a sphere 4/3 πr
◀ Previous3 / 4Next ▶
Density and unit conversions
Density and unit conversions
).
Worked example: a paving slab of mass 73 kg has dimensions 40 mm × 500 mm × 850 mm. Convert to metres: 0.040 × 0.500 × 0.850 = 0.017 m3. Density = 73 ÷ 0.017 = 4.3 × 103 kg m−3.
Conversion rules: converting a larger unit to a smaller one, multiply (125 m = 12 500 cm)

smaller to larger, divide (5 g = 0.005 kg). For squared or cubed units, square or cube the conversion factor: 1 mm3 = (1/1000)3 m3 = 1 × 10−9 m31 cm3 = 1 × 10−6 m3.
◀ Previous4 / 4
1Upthrust, Archimedes’ principle and pressure in fluids2Upthrust, Archimedes’ principle and pressure in fluids3Upthrust, Archimedes’ principle and pressure in fluids4Upthrust, Archimedes’ principle and pressure in fluids
Upthrust, Archimedes’ principle and pressure in fluids
Upthrust, Archimedes’ principle and pressure in fluids
Archimedes’ principle: an object submerged in a fluid at rest experiences an upward buoyancy force (upthrust) equal to the weight of the fluid displaced by the object.
1 / 4Next ▶
Upthrust, Archimedes’ principle and pressure in fluids
1

The object sinks until the weight of fluid displaced equals its own weight

it floats when the upthrust equals its weight.
2

Method: (1) find the volume of the submerged part,
3

which equals the volume of fluid displaced

(2) the mass of fluid is m = ρV(3) upthrust U = mg = ρfVg.(you need this only to know how much fluid was displaced)
4

Boats float because they displace an amount of water equal to their weight.
5

Pressure in a fluid increases with depth: p = p0 + ρgh.
6

Worked example: atmospheric pressure is 100 kPa and sea water has density 1020 kg m
◀ Previous2 / 4Next ▶
Upthrust, Archimedes’ principle and pressure in fluids
Upthrust, Archimedes’ principle and pressure in fluids
−3
.
At what depth is the total pressure 250 kPa?
The extra pressure is 150 kPa = ρgh

so h = 150 000 ÷ (1020 × 9.81) = 15 m (answer D).
Worked example: an iceberg of density 917 kg m−3 and volume Vi floats in seawater of density 1020 kg m−3. Weight = upthrust: 917Vig = 1020Vsubg

so Vsub = 0.90Vi and the fraction above the water is 0.10Vi (answer A).
◀ Previous3 / 4Next ▶
Density and Archimedes’ principle: An unloaded ship (a) floats higher than the same ship when loaded (b), because the loaded ship has a higher average density and sinks deeper.
Upthrust, Archimedes’ principle and pressure in fluids
◀ Previous4 / 4
1Viscosity, Stokes’ law and Core Practical 42Viscosity, Stokes’ law and Core Practical 43What the symbols mean:4Viscosity, Stokes’ law and Core Practical 45Viscosity, Stokes’ law and Core Practical 46Viscosity, Stokes’ law and Core Practical 47Viscosity, Stokes’ law and Core Practical 4
Viscosity, Stokes’ law and Core Practical 4
Viscosity, Stokes’ law and Core Practical 4
Viscosity is a fluid’s resistance to flow: for liquids it decreases as the temperature increases (thicker oils become runnier when heated), and it is measured in Pa s. A sphere moving slowly through a fluid with laminar flow experiences a viscous drag given by Stokes’ law: Fd = 6πηrv

where η is the viscosity, r the radius and v the speed.
Worked example: a ball bearing of radius 5.0 mm falls at a constant speed of 0.030 m s−1 in oil of viscosity 0.3 Pa s and density 900 kg m−3.
Radius = 5.0 × 10
−3
m.
F
1 / 7Next ▶
Viscosity, Stokes’ law and Core Practical 4
Viscosity, Stokes’ law and Core Practical 4
d
= 6 × π × 0.3 × 5.0 × 10
× 0.03 = 8.5 × 10
−4
N.
◀ Previous2 / 7Next ▶
What the symbols mean:
1

At constant (terminal) speed the forces balance: W = F
2

+ U.
3

W = work done = energy transferred (J) · F = force (N) · d, s or x = distance moved in the direction of the force (m)
4

Core Practical 4 (viscosity of a liquid): allow small spheres of known weight to fall through the fluid to terminal velocity.
◀ Previous3 / 7Next ▶
Viscosity, Stokes’ law and Core Practical 4
1

Independent variable: weight (or radius) of ball

dependent: terminal velocitycontrols: fluid and temperature.
2

Apparatus: long measuring cylinder, viscous liquid (thin oil or washing-up liquid), stand and clamp, metre rule, three rubber bands, steel ball bearings of different sizes, digital scales, vernier calipers, stopwatch, magnet.
3

1
4

Weigh the balls, measure the radii with vernier calipers and calculate their density.
5

2
6

Put three rubber bands round the tube: the top one far enough below the surface for the ball to be at terminal velocity, the other two 10 to 15 cm apart.
◀ Previous4 / 7Next ▶
Viscosity, Stokes’ law and Core Practical 4
Viscosity, Stokes’ law and Core Practical 4
3
Release the ball and time it between the bands (lap timing, or two people with two stopwatches)

measure the distances d
and d
.
4
Repeat at least three times for each ball size. Remove the balls with a magnet against the outside wall.
◀ Previous5 / 7Next ▶
Viscosity, Stokes’ law and Core Practical 4
1

Analysis: at terminal velocity Ws = Fd + U, with Ws = (4/3)πr3ρsg, Fd = 6πηrv and U = (4/3)πr3ρfg.
2

Substituting and rearranging:
3

η = 2r
4

g(ρ
5

s
6

− ρ
◀ Previous6 / 7Next ▶
Viscosity, Stokes’ law and Core Practical 4
Viscosity, Stokes’ law and Core Practical 4
f
) ÷ 9v
term
Errors: clamp the ruler vertically and close to the tube

the ball must reach terminal velocity before the first markthe cylinder must be wide compared with the ball to avoid turbulencethe ball must fall in the centre.
Safety: clamp the cylinder

clean spills at onceavoid fluid in the eyes.
◀ Previous7 / 7
1Hooke’s law and force-extension graphs · Hooke’s law and for2Elastic limit · Yield point3Plastic deformation4Plastic deformation
Hooke’s law and force-extension graphs · Hooke’s law and force-extension graphs · Limit of proportionality
Hooke’s law and force-extension graphs
A material obeys Hooke’s law if the extension is directly proportional to the applied force (load) up to the limit of proportionality: F = kΔx

where k is the spring constant (N m−1), a measure of stiffness: the larger k, the stiffer the material.
Hooke’s law and force-extension graphs
It applies to compression as well as extension.
On a force-extension graph, the Hooke’s law region is a straight line through the origin whose gradient equals k.
Limit of proportionality
the point beyond which extension is no longer proportional to force

the graph starts to curve.
1 / 4Next ▶
Elastic limit · Yield point
Elastic limit
the maximum extension from which the material still returns to its original length when the force is removed.
It is always at or after the limit of proportionality.
Yield point
where the material begins to deform plastically with a large extension for little extra force.
◀ Previous2 / 4Next ▶
Plastic deformation
1

permanent deformation: the material does not return to its original shape when the force is removed.
2

It is very common to be asked to define or identify these on a graph

so practise sketching and labelling them.
3

Viscous drag is a resistive force that acts against an object moving through a fluid.
4

A fluid with a higher viscosity flows more slowly

so its flow rate is lower.
5

Viscosity can also be expressed in N s m−2

which is equivalent to Pa s.
◀ Previous3 / 4Next ▶
Force against extension graph with a straight line through the origin that curves after the limit of proportionality
Plastic deformation
Force against extension graph with a straight line through the origin that curves after the limit of proportionality" loading= - Dr Khaled Dabour Academy⤢ Enlarge
Plastic deformation
In laminar flow, the layers of fluid all move in the same direction and do not mix.
◀ Previous4 / 4
1Elastic strain energy2Elastic strain energy3Elastic strain energy4Elastic strain energy5Elastic strain energy
Elastic strain energy
Elastic strain energy
Work has to be done to stretch a material.
1 / 5Next ▶
Elastic strain energy
Elastic strain energy
Before the elastic limit (while Hooke’s law is obeyed), all the work done is stored as
elastic strain energy
.
The work done is the area under the force-extension graph, whether or not the material obeys Hooke’s law.
For the linear region the area is a right-angled triangle: E = ½FΔx = ½kΔx
2
◀ Previous2 / 5Next ▶
Elastic strain energy
Elastic strain energy
For a non-linear region, split the area into geometric shapes and add them,
and count any remaining squares, converting each square using the axes: if each small square is 0.1 N high and 0.01 m wide, it represents 0.001 N m.
Worked example: the shapes give 0.025 + 0.05 + 0.75 + 1.5 + 0.015 = 2.34 J.
1
Counted squares: 7 + 13 = 20

20 × 0.001 = 0.02 J.
Total = 2.36 J

so the work done is 2.4 J to the same significant figures as the data.
◀ Previous3 / 5Next ▶
Elastic strain energy
1

3
2

If your leftover squares seem to exceed the rest of the graph, you have forgotten to convert squares to energy.
3

4
4

Always check units of force and extension (for example mm to m).
◀ Previous4 / 5Next ▶
Shaded triangle under a force-extension graph showing elastic energy stored at 0.10 m and the extra energy up to 0.20 m
Elastic strain energy
◀ Previous5 / 5
1Stress, strain, Young modulus and Core Practical 52Young modulus3Young modulus4Young modulus
Stress, strain, Young modulus and Core Practical 5
Stress, strain, Young modulus and Core Practical 5
Stress = force ÷ cross-sectional area (Pa)

strain = extension ÷ original length (no units).
1 / 4Next ▶
Young modulus
1

The
2

E = stress ÷ strain is the gradient of the straight part of the stress-strain graph and is a property of the material, unlike k.
3

On a stress-strain graph, the ultimate tensile stress is the maximum stress (for example breaking stress 190 MPa),
4

and plastic deformation starts where the graph curves.

(for example at a stress of 130 MPa)
5

Ductile materials (most metals, particularly copper, gold, silver) deform plastically before breaking

brittle materials fracture with no plastic region.
◀ Previous2 / 4Next ▶
Young modulus
Young modulus
Core Practical 5 (Young modulus of a wire): clamp a long wire horizontally over a pulley (or vertically from the ceiling) with a load, with a reference marker (sticky tape) on the wire to measure extension. Independent variable: load

dependent: extension.
1
Measure the original length with a metre rule, to the marker.
2
Measure the diameter with a micrometer at several points and in two perpendicular directions, and take the mean (area = πd
/4).
◀ Previous3 / 4Next ▶
Young modulus
Young modulus
3
Add masses in steps, record the scale reading of the marker each time, and calculate extension.
4
Plot stress against strain, or force against extension

Young modulus = gradient of stress-strain, or gradient × L ÷ A for force-extension.
To reduce uncertainty: use a long thin wire so the extension is larger, take pairs of diameter readings, avoid overloading beyond the elastic limit and check the wire returns to zero extension when unloaded. Wear goggles in case the wire snaps.
◀ Previous4 / 4
1Worked examples2Worked examples
Worked examples
1

Worked example 1. A spring has k = 80 N m−1. Calculate the energy stored when it is extended by 6.0 cm. [2]
2

E = ½kΔx2 = ½ × 80 × 0.0602 = 0.144 J.
3

Worked example 2. A steel wire of length 2.0 m and diameter 0.80 mm is loaded with 50 N and extends by 1.5 mm. Calculate the Young modulus. [4]
4

A = π(0.40 × 10−3)2 = 5.03 × 10−7 m2

stress = 50 ÷ 5.03 × 10−7 = 9.9 × 107 Pastrain = 1.5 × 10−3 ÷ 2.0 = 7.5 × 10−4E = 1.3 × 1011 Pa.
5

Worked example 3. Distinguish between the limit of proportionality and the elastic limit. [2]
6

Limit of proportionality: the point beyond which force and extension are no longer proportional. Elastic limit: the point beyond which the material no longer returns to its original length when the force is removed. The elastic limit is after or at the limit of proportionality.
1 / 2Next ▶
Worked examples
1

Worked example 4. State Archimedes’ principle. [1]
2

The upthrust on a submerged object equals the weight of fluid it displaces.
◀ Previous2 / 2
Key terms
Term Meaning
Density Mass per unit volume.
Upthrust Upward force on a body in a fluid equal to weight of fluid displaced.
Viscosity A fluid’s resistance to flow.
Terminal velocity Constant velocity when the driving and resistive forces balance.
Hooke’s law Extension is proportional to force up to the limit of proportionality.
Elastic limit Maximum extension from which the material returns to original length.
Young modulus Stress divided by strain in the elastic region.
Plastic deformation Permanent deformation after removal of force.
1Avoid these mistakes2Avoid these mistakes
Avoid these mistakes
1Avoid this
Confusing the limit of proportionality, elastic limit and yield point.Avoid this
2Avoid this
Using diameter in place of radius in Stokes’ law or area calculations.Avoid this
3Avoid this
Forgetting to convert squares on the graph to energy.Avoid this
1 / 2Next ▶
Avoid these mistakes
4Avoid this
Saying that the spring constant is a property of the material alone (it depends on shape; Young modulus is the material property).Avoid this
◀ Previous2 / 2
Accepted payment methods