Curriculum
Course: AP PHYSICS 2
Login

Curriculum

AP PHYSICS 2

Text lesson

11.3 Resistance, Resistivity, and Ohm’s Law

11.3 Resistance, Resistivity, and Ohm’s Law — AP PHYSICS 2: ALGEBRA-BASED notes: You will be able to describe the resistance of a conductor from its material, length and cross-sectional area, apply Ohm’s law to a conductive element, and find the resistance of an ohmic element from the slope of a graph of current against potential difference.

Resistance is a measure of the degree to which an object opposes the movement of electric charge.
When a potential difference is applied across a conductor, the charge carriers, usually electrons, move through the material and collide with its atoms.
Each collision transfers some of their energy to the material.
The more strongly the object opposes this motion, the smaller the current it carries for a given potential difference.
Resistance
Resistance R is measured in ohms (Ω).
One ohm is equal to one volt per ampere, so 1 Ω = 1 V/A.
Resistance is a property of a particular object or circuit element, not of a material alone.
The resistance of a conductor with uniform geometry depends on three things: the material it is made from, its length, and its cross-sectional area.
The relationship is R = ρL / A
What the symbols mean
R = resistance (Ω)
ρ = resistivity (Ω m)
L = length (m)
A = cross-sectional area (m2)
Where R is the resistance in ohms (Ω), ρ (rho) is the resistivity in ohm metres (Ω·m), L is the length of the conductor in metres (m), and A is its cross-sectional area in square metres (m2).
Resistance is directly proportional to length, because a longer conductor gives charge carriers more collisions.
Resistance is inversely proportional to cross-sectional area, because a wider conductor gives charge carriers more parallel paths through the material.
Resistivity is a fundamental property of a material that depends on its atomic and molecular structure and quantifies how strongly the material opposes the motion of electric charge.
It does not depend on the size or shape of the sample.
Lengths must be in metres and areas in square metres before the formula is used.
A diameter d gives the area A = π(d/2)2.
Silver1.59 × 10−8
Copper1.69 × 10−8
Aluminium2.83 × 10−8
Tungsten5.6 × 10−8
Carbon3.5 × 10−5
Glassabout 1 × 1013
Resistivity ρ (Ω·m)
More to know
The table shows why metals are used as conductors and glass as an insulator: the resistivities differ by more than twenty orders of magnitude.
Good conductors have very small resistivities, and insulators have very large ones.
Uniform cylinder - Length, area, resistivity - R = ρL/A" loading= - Dr Khaled Dabour Academy
Uniform cylinderLength, area, resistivityR = ρL/A
The resistivity of a conductor typically increases with temperature.
At higher temperatures the atoms of the material vibrate with greater amplitude, so charge carriers collide with them more often and their motion is impeded more strongly.
Resistivity values are normally quoted at 20 °C for this reason.
Temperature
Within an idealised ohmic model, the resistivity of the material is treated as constant regardless of temperature, so the resistance of the element depends only on its shape.
This model is only an approximation: real conductors show a temperature-dependent resistivity, and it should be used only over a range of temperatures where the resistance is effectively constant.
Ohm’s law relates the current, resistance and potential difference across a conductive element of a circuit: V = IR
What the symbols mean
V = potential difference (V)
I = current (A)
R = resistance (Ω)
Here V is the potential difference across the element in volts (V), I is the current through it in amperes (A), and R is its resistance in ohms (Ω).
For a given resistor, doubling the potential difference doubles the current.
A material that obeys Ohm’s law has a constant resistance for all currents, and it is called an ohmic material.
A material or element that does not obey Ohm’s law has a resistance that changes with current or potential difference, and it is called nonohmic.
Filament lamps, semiconductors and liquid conductors are common nonohmic elements.
In a filament lamp the resistance increases as the filament heats up, so its current does not rise in proportion to the potential difference.
A graph of current I against potential difference V is called an I–V graph.
For an ohmic element the graph is a straight line through the origin.
The slope of the line is slope = ΔI / ΔV = 1 / R
So the resistance is R = 1/slope.
For a line of slope 0.25 A/V, the resistance is 1/0.25 Ω = 4.0 Ω.
Graphs drawn the other way round, with potential difference on the vertical axis and current on the horizontal axis, have a slope equal to R itself.
For a nonohmic element the graph is curved or has a changing slope.
The resistance at any one point is then found from the ratio V/I at that point on the graph, not from a single slope.
A resistor can convert electrical energy into thermal energy as charge carriers collide with atoms.
This is why a resistor or a filament warms up when a current passes through it.
The thermal energy raises the temperature of the resistor and can also warm its surroundings.
Heating
Heating is therefore an unavoidable effect of resistance in any real conductor carrying a current, and it is the reason that a fuse or a heater works.
Example 1 · Resistance of a copper wire
Question
A copper wire is 1.2 m long and has a cross-sectional area of 1.2 × 10−8 m2. Its temperature is 20 °C, so the resistivity of copper is 1.69 × 10−8 Ω·m. Find the resistance of the wire, and the current it carries when it is connected to a 10 V battery.
1
R = ρL/A = (1.69 × 10−8 Ω·m)(1.2 m)/(1.2 × 10−8 m2) = 1.69 Ω.
2
Then by Ohm’s law, I = V/R = 10 V / 1.69 Ω = 5.9 A.
Answer
The resistance is 1.7 Ω, and the current is 5.9 A.
Example 2 · Effect of diameter on resistance
Question
A copper wire of length 2.0 m has a diameter of 0.50 mm. Find its resistance. A second copper wire of the same length has twice the diameter. State the resistance of the second wire.
1
The radius is 0.25 mm = 2.5 × 10−4 m, so A = π(2.5 × 10−4 m)2 = 1.96 × 10−7 m2.
2
Then R = (1.69 × 10−8 Ω·m)(2.0 m)/(1.96 × 10−7 m2) = 0.17 Ω.
3
Doubling the diameter multiplies the area by 22 = 4, so the new resistance is 0.17 Ω / 4 = 0.043 Ω.
4
The first wire has a resistance of 0.17 Ω, and the second wire has a resistance of 0.043 Ω, one quarter of the first.
Example 3 · Resistance from an I–V graph
Question
A student measures the current through an ohmic resistor at two potential differences. At 2.0 V the current is 0.40 A, and at 6.0 V the current is 1.20 A. Find the resistance of the resistor.
1
The slope of the I–V graph is ΔI/ΔV = (1.20 A − 0.40 A)/(6.0 V − 2.0 V) = 0.80 A/4.0 V = 0.20 A/V.
2
Then R = 1/slope = 1/(0.20 A/V) = 5.0 Ω.
3
Check: V/I = 2.0 V/0.40 A = 5.0 Ω.
Answer
The resistance is 5.0 Ω. The two points agree, which is consistent with the resistor being ohmic.
Treating resistivity as if it depended on the length or area of the sample.
Resistivity is a property of the material only; resistance depends on ρ, L and A.
Writing resistance as proportional to the cross-sectional area.
Resistance is inversely proportional to A, so a wider wire has a smaller resistance.
Using the diameter of a wire in the formula for A.
The area is π(d/2)2, so the diameter must be halved to give the radius before the area is found.
Forgetting unit conversion.
Lengths in millimetres or areas in mm2 must be converted to metres and square metres before the formula is used.
Reading the slope of an I–V graph as R
For a current–potential difference graph the slope is 1/R, so R = 1/slope.
Assuming a filament lamp is ohmic
Its resistance rises as it heats, so it is nonohmic and its I–V graph is curved.
Accepted payment methods