Curriculum
Course: College Physics for AP Courses 2e
Login

Curriculum

College Physics for AP Courses 2e

Unit 8: Linear Momentum and Collisions

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 9: Statics and Torque

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 10: Rotational Motion and Angular Momentum

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 11: Fluid Statics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 12: Fluid Dynamics and Its Biological and Medical Applications

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 13: Temperature, Kinetic Theory, and the Gas Laws

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 14: Heat and Heat Transfer Methods

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 15: Thermodynamics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 16: Oscillatory Motion and Waves

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 17: Physics of Hearing

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 18: Electric Charge and Electric Field

0/36 Dr Dabour Hub Science Diagram and Course Material

Unit 19: Electric Potential and Electric Field

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 20: Electric Current, Resistance, and Ohm's Law

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 21: Circuits and DC Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 22: Magnetism

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 23: Electromagnetic Induction, AC Circuits, and Electrical Technologies

0/52 Dr Dabour Hub Science Diagram and Course Material

Unit 25: Geometric Optics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 26: Vision and Optical Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 27: Wave Optics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 28: Special Relativity

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 29: Quantum Physics

0/35 Dr Dabour Hub Science Diagram and Course Material
Text lesson

14.5 Conduction

14.5 Conduction — COLLEGE PHYSICS FOR AP COURSES notes: You will be able to calculate the rate of conductive heat transfer through a material, determine the temperature difference or thermal conductivity from that rate, explain conduction in terms of molecular collisions, and compare the conductivities of common substances.

A fireplace heats a room by all three mechanisms at once. Radiation supplies most of the heat that enters the room, while conduction through the walls and convection through the chimney and gaps around the windows contribute less. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Three ways heat moves
Three ways heat moves: A fireplace heats a room by all three mechanisms at once. Radiation supplies most of the heat that enters the room, while conduction through the walls and convection through the chimney and gaps around the windows contribute less." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Three ways heat moves
Heat can travel from one place to another by three mechanisms: conduction, convection, and radiation. Each one has its own characteristics

but all three transfer heat for the same reason: there is a temperature difference between two regions.
Radiation is heat transfer by electromagnetic waves, such as microwaves, infrared radiation, or visible light

which are emitted or absorbed by objects. An obvious example is the warming of the Earth by the Sun. A less obvious example is the thermal radiation your own body emits. The later lessons discuss convection and radiation in detailthis lesson focuses on conduction.
Check your understanding: Name an example from daily life, different from the ones in the text, for each mechanism of heat transfer.
Conduction: heat moves into your hands as you hold a hot cup of coffee. Convection: heat moves through the milk as a barista steams cold milk to make hot cocoa. Radiation: heat reaches a cold cup of coffee inside a microwave oven

which warms it.
Insulation limits conduction of heat through a wall or roof. In winter it keeps indoor heat from escaping, and in summer it keeps outdoor heat from entering. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Why the floor feels cold
Why the floor feels cold: Insulation limits conduction of heat through a wall or roof. In winter it keeps indoor heat from escaping, and in summer it keeps outdoor heat from entering." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

Walk barefoot from a carpet onto a kitchen tile floor in a cold house and the tiles feel much colder, even though the carpet and the tiles are at the same temperature.
2

The difference is in the rate of heat transfer.
3

Heat leaves your skin faster when it touches the tiles than when it touches the carpet,

so in the same time interval your skin temperature drops further on the tiles.
1Molecular collisions and what drives conduction2Molecular collisions and what drives conduction
Molecular collisions and what drives conduction
Molecular collisions and what drives conduction
Some materials conduct thermal energy much faster than others. In general, good conductors of electricity, such as metals like copper, aluminum, gold, and silver, are also good conductors of heat. Insulators of electricity, such as wood, plastic, and rubber, are poor conductors of heat.
Conduction happens at the molecular level.
The average kinetic energy of a molecule in a hot body is higher than that of a molecule in a colder body.
When two molecules collide, energy passes from the molecule with more kinetic energy to the one with less.
The sum of all these collisions produces a net flux of heat from the hot body to the cold body.
Because of this, the rate of heat flow depends on the temperature difference: boiling water causes a more severe burn than hot tap water.
1 / 2Next ▶
Molecules on the hot side have high energy and lose some of it in collisions at the contact surface, while molecules on the cold side gain energy from those collisions. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Molecular collisions and what drives conduction
Molecular collisions and what drives conduction: Molecules on the hot side have high energy and lose some of it in collisions at the contact surface, while molecules on the cold side gain energy from those collisions." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Molecular collisions and what drives conduction
If the two temperatures are equal, the net heat transfer rate drops to zero and the bodies are in thermal equilibrium.
Conduction also depends on the cross-sectional area through which heat flows

because the number of collisions increases with area. If you press your palm against a cold wall, your hand cools faster than if you touch the wall with only a fingertip.
◀ Previous2 / 2
1Thickness and the conduction equation2Thickness and the conduction equation
Thickness and the conduction equation
1

The thickness of the material is the third factor.
2

Suppose a slab has different temperatures on its two faces, with the left face warmer than the right

so heat flows from left to right.
3

Heat moves across the slab through a chain of molecular collisions, and the thicker the slab, the longer it takes to transfer the same amount of heat.
4

This is why thick clothing keeps you warmer than thin clothing in winter, and why Arctic mammals rely on thick blubber.
5

The rate of conductive heat transfer depends on four factors: the surface area A, the temperature difference ΔT, the thermal conductivity k of the substance, and the thickness d. The rate is proportional to A, ΔT, and k, and inversely proportional to d. The equation for a slab is:
6

Q/t = k × A × ΔT / d
1 / 2Next ▶
A rectangular bar of material, such as window glass or walrus blubber, with a warmer face on the left and a cooler face on the right. Heat flow through the bar grows with area, temperature difference, and conductivity, and shrinks as the bar gets thicker. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Thickness and the conduction equation
Thickness and the conduction equation: A rectangular bar of material, such as window glass or walrus blubber, with a warmer face on the left and a cooler face on the right. Heat flow through the bar grows with area, temperature difference, and conductivity, and shrinks as the bar gets thicker." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

where Q/t is the rate of heat transfer in watts (joules per second), k is the thermal conductivity in W/(m·°C), A is the surface area in m2, d is the thickness in m, and ΔT is the temperature difference across the slab in °C. Each value of k is a property of the material and describes how readily it conducts heat.
2

The table below gives representative thermal conductivities at temperatures near 0 °C.
3

Metals have the largest values because they contain many free electrons, the same property that makes them good electrical conductors. This is why cooking utensils are usually made from good conductors.
Substance Thermal conductivity k (W/(m·°C))
Silver 420
Copper 390
Gold 318
Aluminum 220
Steel (iron) 80
Steel (stainless) 14
Ice 2.2
Glass (average) 0.84
Concrete brick 0.84
Water 0.6
Fatty tissue (without blood) 0.2
Asbestos 0.16
Plasterboard 0.16
Wood 0.08 to 0.16
Snow (dry) 0.10
Cork 0.042
Glass wool 0.042
Wool 0.04
Down feathers 0.025
Air 0.023
Styrofoam 0.010
◀ Previous2 / 2
1Insulation and the R-factor2Insulation and the R-factor
Insulation and the R-factor
Insulation and the R-factor
Good insulators are made by combining a low conductivity with a large thickness. The smaller k is and the larger d is, the better the insulation. The ratio d/k is therefore large for a good insulator. This ratio is called the R-factor, and the rate of conductive heat transfer is inversely proportional to R.
R-factors for household insulation, refrigerators, and similar products are still quoted in non-metric units of ft2·°F·h/Btu, although the unit is often left unstated.
One British thermal unit (Btu) is the energy needed to raise the temperature of 1.0 lb of water by 1.0 °F.
Representative values are an R-factor of 11 for 3.5-inch-thick fiberglass batts,

which is typical for walls,and an R-factor of 19 for 6.5-inch-thick batts,which is typical for ceilings.
In cold climates, thicker batts may be used in walls and ceilings.
1 / 2Next ▶
A fiberglass batt insulates a wall or ceiling by slowing heat transfer between the inside of a building and the outside environment. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Insulation and the R-factor
◀ Previous2 / 2
Limits of conduction
Limits of conduction
Conduction is caused by the random motion of atoms and molecules.
It is therefore an ineffective way to move heat over long distances or over long periods.
If the atmosphere transported heat only by conduction, the Earth would be bitterly cold at night and extremely hot during the day.
Likewise, a car engine would overheat unless the excess heat from the pistons were removed by a more efficient process than conduction.
1Example 14.5: Heat conduction through an ice box2Example 14.5: Heat conduction through an ice box3Example 14.5: Heat conduction through an ice box4Example 14.6: Temperature difference across an aluminum pan5Example 14.6: Temperature difference across an aluminum pan
Example 14.5: Heat conduction through an ice box
Example 14.5: Heat conduction through an ice box
Problem: A Styrofoam ice box has a total wall area of 0.950 m2 and walls with an average thickness of 2.50 cm. It holds ice, water, and canned drinks at 0 °C, and the cold inside is kept by melting ice. How much ice melts in one day if the box sits in a car trunk at 35.0 °C?
Strategy: The melting ice absorbs heat, and that heat comes from conduction through the walls. Find the conduction rate, multiply by the time to get the net heat

then divide by the heat of fusion to get the mass.
Solution:
1
Knowns: A = 0.950 m2, d = 0.0250 m, k = 0.010 W/(m·°C) for Styrofoam from the table, ΔT = 35.0 °C − 0.0 °C = 35.0 °C, time t = 24 × 3600 s = 86 400 s,
and the heat of fusion of ice Lf = 3.34 × 105 J/kg.
1 / 5Next ▶
Example 14.5: Heat conduction through an ice box
1

2
2

Rate of heat transfer: Q/t = (0.010)(0.950)(35.0)/(0.0250) = 13.3 W.
3

3
4

Heat transferred in one day: Q = (13.3 J/s)(86 400 s) = 1.15 × 106 J.
5

4
6

Mass of ice melted: m = Q/L
◀ Previous2 / 5Next ▶
Example 14.5: Heat conduction through an ice box
1

f
2

= (1.15 × 106 J)/(3.34 × 105 J/kg) = 3.44 kg.
3

Discussion: 3.44 kg is about 7.6 lb

which matches experience: a 4 kg bag of ice per day is typical.
4

Adding warm food or drinks requires some extra ice.
5

Styrofoam has a very low conductivity

so it is a good insulator.
6

Fiberglass, wool, and goose-down feathers are also good insulators, and they all trap many small pockets of air

which conduct heat poorly.
◀ Previous3 / 5Next ▶
Example 14.6: Temperature difference across an aluminum pan
Example 14.6: Temperature difference across an aluminum pan
Problem: Water boils in an aluminum pan on an electric stove element. The bottom of the pan is 0.800 cm thick and 14.0 cm in diameter, and the boiling water evaporates at 1.00 g/s. What is the temperature difference across the bottom of the pan?
Strategy: Conduction through the aluminum is the main heat path

so use the conduction equation and solve it for ΔT.
Knowns in SI units: d = 0.00800 m, A = π(0.0700 m)2 = 1.54 × 10−2 m2, and k = 220 W/(m·°C) for aluminum.
Heat needed to evaporate 1.00 g = 1.00 × 10−3 kg of water, using L
v
= 2.256 × 106 J/kg: 1.00 × 10−3 kg × 2.256 × 106 J/kg = 2256 J.
◀ Previous4 / 5Next ▶
Example 14.6: Temperature difference across an aluminum pan · Check your understanding: doubling every dimension
Example 14.6: Temperature difference across an aluminum pan
Rate of heat transfer, since 1 g evaporates each second: Q/t = 2256 J / 1 s = 2.26 × 103 W.
Solve the conduction equation for ΔT: ΔT = (Q/t) × d / (k × A) = (2256 W)(0.00800 m) / [(220 W/(m·°C))(0.0154 m2)] = 5.33 °C.
Discussion: The burner is red hot

but the inside of the pan stays close to the boiling point of water because the water removes heat at the contact surface. Aluminum conducts so well that a temperature difference of only 5.33 °C is enough to carry 2.26 kW into the pan.
Check your understanding: doubling every dimension
Question: How does the rate of conductive heat transfer change when all spatial dimensions are doubled?
Answer: Area is the product of two spatial dimensions

so it increases by a factor of 2 × 2 = 4. Thickness only doubles. ΔT and k do not depend on size. The rate therefore increases by a factor of 4 / 2 = 2so it doubles.
◀ Previous5 / 5
Key terms
Term Meaning
Conduction Conduction is the transfer of thermal energy through direct molecular collisions, without any bulk movement of the material.
Thermal conductivity (k) Thermal conductivity is a property of a material that describes how fast it conducts heat, measured in W/(m·°C).
Temperature difference (ΔT) The temperature difference is the change in temperature from one face of a material to the other, and it drives conductive heat flow.
Cross-sectional area (A) The cross-sectional area is the area through which heat flows, measured in m2.
Thickness (d) The thickness is the distance heat must travel through a material, measured in m.
Heat flux Heat flux is the net flow of heat from a hotter body to a colder one through the molecular collisions at their contact surface.
Thermal equilibrium Thermal equilibrium is the state in which two bodies have the same temperature, so the net heat transfer between them is zero.
Conductor A conductor is a material that transfers heat or electricity readily, such as a metal.
Insulator An insulator is a material that transfers heat or electricity poorly, such as wood, plastic, or Styrofoam.
R-factor The R-factor is the ratio of thickness to thermal conductivity (d/k); a larger value means better insulation.
British thermal unit (Btu) A Btu is the energy needed to raise the temperature of 1.0 lb of water by 1.0 °F.
1Avoid these mistakes2Avoid these mistakes3Avoid these mistakes
Avoid these mistakes
1Avoid this
Putting thickness or area in centimeters or cm2 into the conduction equation.Avoid this
Convert every length to meters before calculating, because k is given in W/(m·°C).Avoid this
2Avoid this
Assuming that a thicker material conducts heat faster. The rate is inversely proportional to thickness, so thicker materials conduct heat more slowly.Avoid this
3Avoid this
1 / 3Next ▶
Avoid these mistakes
Doubling only the area when all dimensions are doubled.Avoid this
Area is the product of two dimensions, so it grows by a factor of 4, and the rate grows by 4 ÷ 2 = 2 overall.Avoid this
4Avoid this
Confusing the heat transferred (energy in joules) with the rate of heat transfer (power in watts).Avoid this
Multiply the rate by time to get energy, and divide the energy by the heat of fusion or vaporization to get mass.Avoid this
5Avoid this
◀ Previous2 / 3Next ▶
Avoid these mistakes
Thinking carpet and tile are at different temperatures because the tile feels colder.Avoid this
Their temperatures are equal, and the difference in feel comes from the different rates of heat transfer.Avoid this
6Avoid this
Using a temperature of the surroundings instead of the temperature difference across the material when calculating ΔT.Avoid this
◀ Previous3 / 3
Accepted payment methods