Curriculum
Course: College Physics for AP Courses 2e
Login

Curriculum

College Physics for AP Courses 2e

Unit 8: Linear Momentum and Collisions

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 9: Statics and Torque

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 10: Rotational Motion and Angular Momentum

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 11: Fluid Statics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 12: Fluid Dynamics and Its Biological and Medical Applications

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 13: Temperature, Kinetic Theory, and the Gas Laws

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 14: Heat and Heat Transfer Methods

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 15: Thermodynamics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 16: Oscillatory Motion and Waves

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 17: Physics of Hearing

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 18: Electric Charge and Electric Field

0/36 Dr Dabour Hub Science Diagram and Course Material

Unit 19: Electric Potential and Electric Field

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 20: Electric Current, Resistance, and Ohm's Law

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 21: Circuits and DC Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 22: Magnetism

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 23: Electromagnetic Induction, AC Circuits, and Electrical Technologies

0/52 Dr Dabour Hub Science Diagram and Course Material

Unit 25: Geometric Optics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 26: Vision and Optical Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 27: Wave Optics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 28: Special Relativity

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 29: Quantum Physics

0/35 Dr Dabour Hub Science Diagram and Course Material
Text lesson

23.11 Reactance, Inductive and Capacitive

23.11 Reactance, Inductive and Capacitive — COLLEGE PHYSICS FOR AP COURSES notes: You will be able to sketch voltage and current against time for inductive, capacitive and resistive circuits, and calculate inductive reactance, capacitive reactance, and the current or voltage in each simple circuit.

1Inductors and inductive reactance2Inductors and inductive reactance3Inductors and inductive reactance4Inductors and inductive reactance
Inductors and inductive reactance
Inductors and inductive reactance
Many AC circuits contain capacitors and inductors in addition to resistors and an AC voltage source.
In earlier sections we saw how these elements respond to a DC voltage that is switched on or off.
Now we look at how they respond to a sinusoidal AC voltage, starting with an inductor connected directly to an AC source.
In practice the resistance of an inductor can be made so small that it has a negligible effect

so we treat the inductor as having no resistance.
When the voltage is at its maximum, the current in the inductor is zero.
As the voltage drops and becomes negative, the current decreases, reaches zero at the point where the voltage is most negative,

and then becomes negative as it follows the voltage.
1 / 4Next ▶
A sinusoidal AC source in series with an inductor, with a graph showing that the current reaches each peak after the voltage has peaked. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Inductors and inductive reactance
Inductors and inductive reactance: A sinusoidal AC source in series with an inductor, with a graph showing that the current reaches each peak after the voltage has peaked." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

The pattern repeats each cycle.
2

The graph below shows the source and inductor and the voltage and current plotted against time.
3

The current lags behind the voltage because an inductor opposes any change in current.
4

A changing current induces a back emf in the inductor, and this back emf acts as an effective resistance of the inductor to AC.
5

For a sinusoidal voltage applied to an inductor, the voltage leads the current by one-fourth of a cycle

which is a phase angle of 90°.
6

The rms voltage across the inductor is related to the rms current by a version of Ohm’s law: Vrms = IrmsXL.
◀ Previous2 / 4Next ▶
Inductors and inductive reactance
Inductors and inductive reactance
Here Vrms is the rms voltage across the inductor in volts (V), Irms is the rms current in amperes (A), and XL is the inductive reactance in ohms (Ω).
The inductive reactance is defined as XL = 2πfL

where f is the frequency of the AC source in hertz (Hz) and L is the inductance in henries (H).
The product of frequency and inductance has units of ohms,

because a henry is equivalent to an ohm-second,so the reactance acts like an effective resistance.
The inductive reactance depends on both frequency and inductance.
It is proportional to L

because a larger inductance resists changes in current more strongly.
It is also proportional to f

because a higher frequency means the current changes more rapidly.
◀ Previous3 / 4Next ▶
Inductors and inductive reactance
Inductors and inductive reactance
So XL is large at high frequencies and small at low frequencies.
Because inductors impede rapid changes, they block high frequencies more than low ones.
◀ Previous4 / 4
1Capacitors and capacitive reactance2Capacitors and capacitive reactance3Capacitors and capacitive reactance
Capacitors and capacitive reactance
1

Now consider a capacitor connected directly to a sinusoidal AC source.
2

Again we assume that the circuit resistance is negligible compared with the capacitor.
3

At the moment the voltage across the capacitor is at its maximum, the capacitor is fully charged

so the current is zero and the charge flow halts.
4

As the voltage falls, the capacitor discharges and the current becomes negative.
5

When the capacitor is fully discharged, the voltage across it is zero, and the current reaches its largest magnitude.
6

The current then charges the capacitor in the opposite direction until the voltage reaches its most negative value.
1 / 3Next ▶
A sinusoidal AC source in series with a capacitor, with a graph showing that the capacitor voltage follows the current by a quarter of a cycle. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Capacitors and capacitive reactance
Capacitors and capacitive reactance: A sinusoidal AC source in series with a capacitor, with a graph showing that the capacitor voltage follows the current by a quarter of a cycle." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

Throughout the cycle the voltage across the capacitor follows the current by one-fourth of a cycle.
2

Equivalently, the current leads the voltage by 90°.
3

The capacitor limits the current because it can store charge and stop the flow once it is charged.
4

Even though a capacitor is essentially an open circuit to steady current, an AC voltage keeps charging and discharging it

so an rms current flows.
5

The capacitor acts as an effective resistance to AC, and the rms current is given by another version of Ohm’s law: Irms = Vrms/XC.
6

The capacitive reactance is defined as XC = 1/(2πfC)

where C is the capacitance in farads (F).
◀ Previous2 / 3Next ▶
Capacitors and capacitive reactance
Capacitors and capacitive reactance
Its units are ohms, since 1/(hertz × farad) equals volts per ampere.
The capacitive reactance is inversely proportional to the capacitance: a larger capacitor can store more charge and allow more current to flow.
It is also inversely proportional to the frequency: at a higher frequency there is less time to charge the capacitor fully,

so it impedes the current less.
◀ Previous3 / 3
Comparing the three circuit elements
1

A resistor behaves differently from the inductor and the capacitor. The voltage and current are exactly in phase in a resistor, and the rms current is Irms = Vrms/R

where R is the resistance in ohms. There is no frequency dependence in plain resistance. The table summarises the three cases.
2

Inductors and capacitors therefore have opposite effects on AC circuits.
3

An inductor filters out high frequencies

while a capacitor filters out low frequencies.
4

As the frequency goes to zero (DC), XC tends to infinity and the current becomes zero once the capacitor is charged.
5

At very high frequencies XC tends to zero

so the capacitor acts like a simple wire.
Element Phase relationship Opposition to current Frequency dependence
Resistor Voltage and current in phase R None
Inductor Voltage leads current by 90° XL = 2πfL Increases with frequency
Capacitor Current leads voltage by 90° XC = 1/(2πfC) Decreases with frequency
1Example 23.10: Calculating inductive reactance and then curr2Example 23.10: Calculating inductive reactance and then curr3Example 23.11: Calculating capacitive reactance and then cur4Example 23.11: Calculating capacitive reactance and then cur
Example 23.10: Calculating inductive reactance and then current
Example 23.10: Calculating inductive reactance and then current
A 3.00 mH inductor is connected to AC sources at 60.0 Hz and at 10.0 kHz. (a) Find the inductive reactance at each frequency. (b) Find the rms current at each frequency if the applied rms voltage is 120 V.
Strategy: Use XL = 2πfL to find the reactance

then use Ohm’s law, Irms = Vrms/XL, to find the current.
Solution for (a): L = 3.00 × 10−3 H. At 60.0 Hz, XL = 2π(60.0 Hz)(3.00 × 10−3 H) = 1.13 Ω. At 10.0 kHz, XL = 2π(1.00 × 104 Hz)(3.00 × 10−3 H) = 188 Ω.
Solution for (b): At 60.0 Hz, Irms = 120 V/1.131 Ω = 106 A. At 10.0 kHz, Irms = 120 V/188.5 Ω = 0.637 A.
Discussion: The inductor reacts very differently at the two frequencies.
At the higher frequency its reactance is large and the current is small

which shows that high frequencies are impeded the most.
1 / 4Next ▶
Example 23.10: Calculating inductive reactance and then current
Example 23.10: Calculating inductive reactance and then current
This is why a large inductor in series with a sound system can reduce high-frequency sound output.
Even though the resistance is negligible, the AC current is not extremely large

because the inductive reactance limits it.
◀ Previous2 / 4Next ▶
Example 23.11: Calculating capacitive reactance and then current
1

A 5.00 µF capacitor is connected to AC sources at 60.0 Hz and at 10.0 kHz. (a) Find the capacitive reactance at each frequency. (b) Find the rms current at each frequency if the applied rms voltage is 120 V.
2

Strategy: Use XC = 1/(2πfC) to find the reactance

then use Irms = Vrms/XC to find the current.
3

Solution for (a): C = 5.00 × 10−6 F. At 60.0 Hz, XC = 1/[2π(60.0 Hz)(5.00 × 10−6 F)] = 531 Ω. At 10.0 kHz, XC = 1/[2π(1.00 × 104 Hz)(5.00 × 10−6 F)] = 3.18 Ω.
4

Solution for (b): At 60.0 Hz, Irms = 120 V/530.5 Ω = 0.226 A. At 10.0 kHz, Irms = 120 V/3.183 Ω = 37.7 A.
5

Discussion: The capacitor reacts in exactly the opposite way to the inductor.
6

At the higher frequency its reactance is small and the current is large

because the capacitor has little time to charge and stop the current.
◀ Previous3 / 4Next ▶
Example 23.11: Calculating capacitive reactance and then current
1

Capacitors impede low frequencies the most.
2

A capacitor in series with a sound system can remove the 60 Hz hum.
3

Although a capacitor is basically an open circuit, there is an rms current because the AC voltage keeps charging and discharging it.
◀ Previous4 / 4
Key terms
Term Meaning
Inductive reactance The effective resistance of an inductor to AC, equal to 2πfL and measured in ohms.
Capacitive reactance The effective resistance of a capacitor to AC, equal to 1/(2πfC) and measured in ohms.
Inductance The property of an inductor that determines how strongly it opposes changes in current, measured in henries.
Capacitance The ability of a capacitor to store charge for a given voltage, measured in farads.
Back emf The voltage induced in an inductor by a changing current, which opposes that change.
Phase angle The angle, in degrees or fractions of a cycle, by which the voltage and current in a circuit element are out of step.
Lag A situation in which one quantity reaches its peak after another; the current lags the voltage in an inductor.
Lead A situation in which one quantity reaches its peak before another; the voltage leads the current in an inductor.
Frequency The number of complete cycles of the AC source per second, measured in hertz.
RMS voltage The root-mean-square voltage of an AC source, used with Ohm’s law in AC circuits.
RMS current The root-mean-square current in an AC circuit, found by dividing the rms voltage by the reactance or resistance.
Effective resistance to AC The opposition to alternating current offered by an inductor or capacitor, which behaves like a resistance but depends on frequency.
1Avoid these mistakes2Avoid these mistakes3Avoid these mistakes
Avoid these mistakes
1Avoid this
Saying that current leads voltage in an inductor.Avoid this
In an inductor the voltage leads the current by 90°, while in a capacitor the current leads the voltage.Avoid this
2Avoid this
Using the capacitor formula for an inductor or the inductor formula for a capacitor.Avoid this
XL = 2πfL increases with frequency, but XC = 1/(2πfC) decreases with frequency.Avoid this
1 / 3Next ▶
Avoid these mistakes
3Avoid this
Forgetting to convert units before calculating, such as using kHz instead of Hz, mH instead of H, or µF instead of F.Avoid this
4Avoid this
Thinking that a capacitor passes a steady DC current.Avoid this
Once a DC source has charged a capacitor, the current is zero, but an AC voltage keeps it charging and discharging.Avoid this
5Avoid this
◀ Previous2 / 3Next ▶
Avoid these mistakes
Confusing peak and rms values. Ohm’s law in this section uses rms voltage and rms current.Avoid this
6Avoid this
Assuming that a large reactance means a large current. Reactance limits current, so a large reactance gives a small rms current.Avoid this
◀ Previous3 / 3
Accepted payment methods