Curriculum
Course: College Physics for AP Courses 2e
Login

Curriculum

College Physics for AP Courses 2e

Unit 8: Linear Momentum and Collisions

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 9: Statics and Torque

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 10: Rotational Motion and Angular Momentum

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 11: Fluid Statics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 12: Fluid Dynamics and Its Biological and Medical Applications

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 13: Temperature, Kinetic Theory, and the Gas Laws

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 14: Heat and Heat Transfer Methods

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 15: Thermodynamics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 16: Oscillatory Motion and Waves

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 17: Physics of Hearing

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 18: Electric Charge and Electric Field

0/36 Dr Dabour Hub Science Diagram and Course Material

Unit 19: Electric Potential and Electric Field

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 20: Electric Current, Resistance, and Ohm's Law

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 21: Circuits and DC Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 22: Magnetism

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 23: Electromagnetic Induction, AC Circuits, and Electrical Technologies

0/52 Dr Dabour Hub Science Diagram and Course Material

Unit 25: Geometric Optics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 26: Vision and Optical Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 27: Wave Optics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 28: Special Relativity

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 29: Quantum Physics

0/35 Dr Dabour Hub Science Diagram and Course Material
Text lesson

23.12 RLC Series AC Circuits

23.12 RLC Series AC Circuits — COLLEGE PHYSICS FOR AP COURSES notes: You will be able to calculate the impedance, phase angle, resonant frequency, power and power factor of an RLC series circuit, draw its diagram, and explain the significance of the resonant frequency.

1Impedance2Impedance3Impedance
Impedance
Impedance
When an inductor, a capacitor and a resistor are all in the same AC circuit, their individual opposition to current does not simply add.
1 / 3Next ▶
The circuit diagram shows a sinusoidal source in series with a resistor, an inductor and a capacitor, with the voltage across each element labelled. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Impedance
Impedance: The circuit diagram shows a sinusoidal source in series with a resistor, an inductor and a capacitor, with the voltage across each element labelled." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

Inductors and capacitors respond to a changing current in opposite ways

so their effects partly or completely cancel each other.
2

The combined effect depends strongly on frequency, and this frequency dependence is the basis of many useful devices, such as radio tuners.
3

An RLC series circuit contains a resistor R, an inductor L and a capacitor C connected in a single loop with an AC voltage source. The combined opposition to current from all three elements is called impedance, symbol Z. It is the AC equivalent of resistance in a DC circuit, and it is measured in ohms (Ω).
4

The current, voltage and impedance in an RLC circuit obey an AC version of Ohm’s law.
5

Before we use it for the whole circuit, it helps to recall the simplest case.
6

When a sinusoidal voltage is applied to a resistor alone, the voltage and the current are exactly in phase with each other,
◀ Previous2 / 3Next ▶
A single resistor is connected to a sinusoidal source, and the graph shows the resistor voltage and current rising and falling together in step. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Impedance
Impedance: A single resistor is connected to a sinusoidal source, and the graph shows the resistor voltage and current rising and falling together in step." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Impedance
so the phase angle between them is zero.
The peak current is the peak voltage divided by the resistance.
For the whole RLC circuit the same form holds: I0 = V0 / Z

where I0 is the peak current in amperes, V0 is the peak source voltage in volts and Z is the impedance in ohms. A larger impedance means a smaller current for the same source voltage.
◀ Previous3 / 3
1How the impedance is built2How the impedance is built3How the impedance is built4How the impedance is built5How the impedance is built6How the impedance is built7How the impedance is built8How the impedance is built
How the impedance is built
How the impedance is built
Conservation of charge requires the current to be the same at every point in a series circuit at every instant.
1
The current through the resistor, the inductor and the capacitor is therefore the same and in phase with itself.
2
What differs is the voltage across each element.
3
1 / 8Next ▶
How the impedance is built
1

The voltage across the inductor leads the current by one-quarter of a cycle.
2

4
3

The voltage across the capacitor lags the current by one-quarter of a cycle.
4

5
5

The voltage across the resistor is exactly in phase with the current.
6

The graph below plots all of these voltages against time on one set of axes. It also shows the total voltage around the loop

where each value is an instantaneous value.
◀ Previous2 / 8Next ▶
The graph shows the resistor, inductor and capacitor voltages together with the current; their sum equals the source voltage, which is out of phase with the current. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
How the impedance is built
How the impedance is built: The graph shows the resistor, inductor and capacitor voltages together with the current; their sum equals the source voltage, which is out of phase with the current." loading= - Dr Khaled Dabour Academy⤢ Enlarge
How the impedance is built
Kirchhoff’s loop rule says that the voltages across the three elements add up to the source voltage at every instant.
◀ Previous3 / 8Next ▶
How the impedance is built
How the impedance is built
The resistor voltage is in phase with the current, the inductor voltage leads by a quarter cycle and the capacitor voltage lags by a quarter cycle.
The inductor and capacitor voltages are therefore out of phase with each other by half a cycle

so they tend to cancel.
They cancel completely only when their peak values are equal.
Because the peak voltages are not in phase, the peak source voltage is not the sum of the three peak voltages.
It is found from V
0
◀ Previous4 / 8Next ▶
How the impedance is built
1

= V
2

R
3

+ (V
4

L
5

− V
6

C
◀ Previous5 / 8Next ▶
How the impedance is built
How the impedance is built
)
where V
, V
and V
are the peak voltages across the resistor, inductor and capacitor.
Using Ohm’s law for each element, the resistor voltage is I
◀ Previous6 / 8Next ▶
How the impedance is built
How the impedance is built
R, the inductor voltage is I
X
and the capacitor voltage is I
.
The common factor I
cancels

which gives the impedance:
◀ Previous7 / 8Next ▶
How the impedance is built
1

XL = 2πfL (inductive reactance, in ohms, with f in hertz and L in henries, H)
2

XC = 1 / (2πfC) (capacitive reactance, in ohms, with C in farads, F)
3

Z = √(R2 + (XL − XC)2) (impedance, in ohms)
4

The same formula covers simpler circuits. For a circuit with no resistor, use R = 0. For a circuit with no inductor, use XL = 0. For a circuit with no capacitor, use XC = 0.
◀ Previous8 / 8
1Phase angle, resonance and the resonant frequency2Phase angle, resonance and the resonant frequency3Phase angle, resonance and the resonant frequency4Phase angle, resonance and the resonant frequency5Phase angle, resonance and the resonant frequency6Phase angle, resonance and the resonant frequency7Phase angle, resonance and the resonant frequency
Phase angle, resonance and the resonant frequency
Phase angle, resonance and the resonant frequency
The phase angle φ is the angle between the source voltage and the current.
1 / 7Next ▶
Phase angle, resonance and the resonant frequency
Phase angle, resonance and the resonant frequency
It is found from tan φ = (X
L
− X
C
) / R.
A positive phase angle means the source voltage leads the current

which happens when the inductor dominates.
◀ Previous2 / 7Next ▶
Phase angle, resonance and the resonant frequency
1

A negative phase angle means the source voltage lags the current

which happens when the capacitor dominates.
2

The reactances depend on frequency in opposite ways.
3

X
4

is large at high frequencies and small at low frequencies

while X
5

is large at low frequencies and small at high frequencies.
6

At some intermediate frequency, the two reactances are equal

so they cancel.
◀ Previous3 / 7Next ▶
Phase angle, resonance and the resonant frequency
Phase angle, resonance and the resonant frequency
At that frequency the impedance is at its minimum value, Z = R, and the current is at its maximum.
This condition is called
resonance
.
Setting XL = XC and solving for the frequency gives the resonant frequency, the frequency at which resonance occurs:
f0 = 1 / (2π√(LC)) (resonant frequency, in hertz)
◀ Previous4 / 7Next ▶
Phase angle, resonance and the resonant frequency
Phase angle, resonance and the resonant frequency
At this frequency the effects of the inductor and capacitor cancel, and the impedance equals the resistance alone.
The resonant frequency is also the
natural frequency
at which the circuit would oscillate if it were not driven by the source.
Resonance in AC circuits is analogous to mechanical resonance, in which a system is forced to oscillate at its own natural frequency.
A radio receiver is an RLC circuit tuned to resonate best at the frequency of the station it should receive. A variable capacitor is often used to change the resonant frequency so that one desired station is received and others are rejected.
◀ Previous5 / 7Next ▶
Phase angle, resonance and the resonant frequency
1

The graph below shows current as a function of frequency for two RLC circuits that differ only in their resistance.
2

Both show a resonant peak at the same frequency.
3

The peak is lower and broader for the circuit with higher resistance.
4

A higher-resistance circuit therefore resonates less strongly and is less selective

which makes it a poorer choice for a radio receiver.
◀ Previous6 / 7Next ▶
Current against frequency for two RLC series circuits with different resistances. Both peak at the same resonant frequency, but the higher-resistance peak is lower and wider. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Phase angle, resonance and the resonant frequency
◀ Previous7 / 7
1Power in RLC series AC circuits2Power factor3Power factor4Power factor
Power in RLC series AC circuits
Power in RLC series AC circuits
When the current changes with frequency, the power delivered to the circuit changes too. In a purely resistive circuit, average power is simply current times voltage. In an RLC circuit, the voltage and current are out of phase

so that simple product no longer gives the average power.
The phase angle is found from tan φ = (XL − XC) / R.
1 / 4Next ▶
Power factor
1

Equivalently, the
2

power factor
3

is cos φ = R / Z.
4

At the resonant frequency, or in a purely resistive circuit, X
5

L
6

= X
◀ Previous2 / 4Next ▶
Power factor
Power factor
C
or X
− X
= 0

so φ = 0 and cos φ = 1.
The voltage and current are then in phase, as expected for a resistor.
At other frequencies the average power is less than at resonance. This happens for two reasons: the voltage and current are out of phase, and the current itself is smaller. It can be shown that the average power delivered by the source is:
◀ Previous3 / 4Next ▶
Power factor
Power factor
Pavg = Irms Vrms cos φ (average power, in watts)
Here Irms = I0 / √2 and Vrms = V0 / √2 are the root-mean-square current and voltage. The quantity cos φ is the power factor

which ranges from 0 to 1. Power factors close to 1 are desirable, for example when designing an efficient electric motor. At the resonant frequency the power factor equals 1.
◀ Previous4 / 4
1Energy transfer in the circuit2Energy transfer in the circuit3Energy transfer in the circuit4Energy transfer in the circuit5Energy transfer in the circuit
Energy transfer in the circuit
Energy transfer in the circuit
Power is delivered to an RLC series circuit and is dissipated only by the resistance.
1 / 5Next ▶
Energy transfer in the circuit
1

The inductor and the capacitor receive energy from the source and return it, transferring energy back and forth between their magnetic and electric fields.
2

The resistor dissipates exactly the power that the source puts into the circuit.
3

This assumes that the inductor and capacitor do not radiate significant electromagnetic waves, such as radio waves

which is the case in this chapter.
4

A useful mechanical picture is a car wheel on a spring with a shock absorber, driven over a corrugated road.
5

1
6

The regularly spaced bumps play the role of the voltage source.
◀ Previous2 / 5Next ▶
Energy transfer in the circuit
Energy transfer in the circuit
2
The shock absorber damps the motion and limits its amplitude, just as the resistance does in the circuit.
3
Energy moves between kinetic energy,
which corresponds to the maximum current and the energy in the inductor,
and potential energy in the spring,
◀ Previous3 / 5Next ▶
A car wheel on a damped spring, driven by bumps in the road, is a mechanical model of the RLC circuit: the shock absorber stands for the resistor and the spring and mass set the resonant frequency. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Energy transfer in the circuit
Energy transfer in the circuit: A car wheel on a damped spring, driven by bumps in the road, is a mechanical model of the RLC circuit: the shock absorber stands for the resistor and the spring and mass set the resonant frequency." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

which corresponds to zero current and the energy in the capacitor’s electric field.
2

4
3

The wheel’s motion is largest when the bumps are hit at the resonant frequency.
4

A pure LC circuit with negligible resistance oscillates at the same resonant frequency as the RLC circuit, f0 = 1 / (2π√(LC)).
5

Because its oscillations last for a long time, it can serve as a frequency standard, for example in the clock circuit of a digital wristwatch.
6

Even a small resistance removes energy from the oscillations

so only a small energy input from the source is needed to keep them going.
◀ Previous4 / 5Next ▶
An LC circuit and a mass on a spring both swap energy back and forth between two forms with no driving force and no friction. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Energy transfer in the circuit
Energy transfer in the circuit: An LC circuit and a mass on a spring both swap energy back and forth between two forms with no driving force and no friction." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Energy transfer in the circuit
The LC circuit is like a mass on a spring with no friction and no driving force: energy moves back and forth between the inductor and the capacitor, just as it moves between kinetic and potential energy in the mass-spring system.
◀ Previous5 / 5
PhET explorations
PhET explorations
The Circuit Construction Kit (AC+DC) virtual lab lets you build circuits from capacitors, inductors, resistors and AC or DC sources. You can inspect the circuit with virtual voltmeters and ammeters

which helps you check the impedance, resonance and power ideas in this section by changing the frequency and the component values yourself.
1Example 23.12: Calculating impedance and current2Example 23.12: Calculating impedance and current3Example 23.13: Calculating resonant frequency and current4Example 23.14: Calculating the power factor and power5Worked examples6Worked examples
Example 23.12: Calculating impedance and current
1

Problem: An RLC series circuit has a resistor of R = 40.0 Ω, an inductor of L = 3.00 mH and a capacitor of C = 5.00 μF. The peak source voltage is V0 = 120 V. (a) Find the impedance at 60.0 Hz and at 10.0 kHz. (b) Find the peak current at each frequency.
2

Strategy: Calculate XL and XC at each frequency, find Z

then use Ohm’s law to find the current.
3

Solution for (a) at 60.0 Hz: XL = 2π(60.0 Hz)(3.00×10−3 H) = 1.13 Ω. XC = 1 / [2π(60.0 Hz)(5.00×10−6 F)] = 530.5 Ω. Then Z = √(40.02 + (1.13 − 530.5)2) = √(2.82×105) Ω ≈ 531 Ω.
4

Solution for (a) at 10.0 kHz: XL = 2π(1.00×104 Hz)(3.00×10−3 H) = 188.5 Ω. XC = 1 / [2π(1.00×104 Hz)(5.00×10−6 F)] = 3.18 Ω. Then Z = √(40.02 + (188.5 − 3.18)2) = √(3.59×104) Ω ≈ 190 Ω.
5

Discussion for (a): In both cases the impedance is nearly equal to the largest single reactance and is clearly not the sum of the individual values. The capacitor dominates at low frequency and the inductor dominates at high frequency.
6

Solution for (b) at 60.0 Hz: I0 = V0 / Z = 120 V / 531 Ω = 0.226 A.
1 / 6Next ▶
Example 23.12: Calculating impedance and current
1

Solution for (b) at 10.0 kHz: I0 = V0 / Z = 120 V / 190 Ω = 0.632 A.
2

Discussion for (b): The current at 60.0 Hz is the same, to three digits, as the current found for the capacitor alone. The current at 10.0 kHz is close to the current found for the inductor alone

because the inductor dominates at this high frequency.
◀ Previous2 / 6Next ▶
Example 23.13: Calculating resonant frequency and current
Example 23.13: Calculating resonant frequency and current
Problem: For the same RLC series circuit (R = 40.0 Ω, L = 3.00 mH, C = 5.00 μF, V0 = 120 V), (a) find the resonant frequency and (b) calculate the peak current at resonance.
Strategy: Use f0 = 1 / (2π√(LC)). At resonance the reactances cancel

so the impedance equals the resistance.
Solution for (a): f0 = 1 / [2π√((3.00×10−3 H)(5.00×10−6 F))] = 1 / [2π(1.22×10−4 s)] = 1.30×103 Hz = 1.30 kHz.
Discussion for (a): The resonant frequency lies between 60.0 Hz and 10.0 kHz, the two frequencies used in Example 23.12. This is expected

because the capacitor dominated at the low frequency and the inductor dominated at the high frequency, and their effects are equal at this intermediate frequency.
Solution for (b): At resonance Z = R = 40.0 Ω

so I0 = V0 / R = 120 V / 40.0 Ω = 3.00 A.
Discussion for (b): The current at resonance is much greater than at the higher and lower frequencies considered for the same circuit in Example 23.12.
◀ Previous3 / 6Next ▶
Example 23.14: Calculating the power factor and power
1

Problem: For the same RLC series circuit with V0 = 120 V, (a) calculate the power factor and phase angle at 60.0 Hz, (b) find the average power at 60.0 Hz and (c) find the average power at the resonant frequency.
2

Strategy and solution for (a): From Example 23.12, Z ≈ 531 Ω at 60.0 Hz.
◀ Previous4 / 6Next ▶
Worked examples
Worked examples
The power factor is cos φ = R / Z = 40.0 Ω / 531 Ω = 0.0753. The phase angle is φ = arccos(0.0753) ≈ 85.7°.
Check: tan φ = (X
C
− X
L
) / R = 529.4 / 40.0 = 13.2

which also gives φ ≈ 85.7°.
◀ Previous5 / 6Next ▶
Worked examples
Worked examples
Discussion for (a): The small power factor shows that the voltage and current are strongly out of phase. The phase angle is close to 90°

which is consistent with the capacitor dominating at this low frequencybecause a pure RC circuit also has its voltage and current about 90° out of phase.
Strategy and solution for (b): The peak current at 60.0 Hz is 0.226 A. Using Pavg = Irms2R with Irms = I0 / √2 gives Pavg = (0.226 A)2(40.0 Ω) / 2 = 1.02 W.
Strategy and solution for (c): At the resonant frequency, cos φ = 1 and the peak current is 3.00 A from Example 23.13. Thus Pavg = (3.00 A)2(40.0 Ω) / 2 = 180 W.
Discussion: Both the current and the power factor are greater at resonance

so the circuit delivers far more power there than at higher or lower frequencies.
◀ Previous6 / 6
Key terms
Term Meaning
RLC series circuit A single loop containing a resistor, an inductor and a capacitor in series with an AC source.
Impedance (Z) The combined opposition to current in an AC circuit, measured in ohms; the AC equivalent of resistance.
Inductive reactance (XL) The opposition an inductor offers to AC current, equal to 2πfL and measured in ohms.
Capacitive reactance (XC) The opposition a capacitor offers to AC current, equal to 1 / (2πfC) and measured in ohms.
Phase angle (φ) The angle between the source voltage and the current, given by tan φ = (XL − XC) / R.
Resonance The condition in which the inductive and capacitive reactances are equal, so the impedance is at its minimum and the current at its maximum.
Resonant frequency (f0) The frequency at which resonance occurs, given by 1 / (2π√(LC)).
Natural frequency The frequency at which a system oscillates when it is not driven by an outside source.
Power factor (cos φ) The ratio R / Z, which ranges from 0 to 1 and sets how much of the apparent power becomes average power.
Average power (Pavg) The power delivered to a circuit averaged over a full cycle, equal to IrmsVrmscos φ.
LC circuit A circuit with an inductor and a capacitor and negligible resistance, which oscillates at the resonant frequency.
1Avoid these mistakes2Avoid these mistakes3Avoid these mistakes4Avoid these mistakes
Avoid these mistakes
1Avoid this
Adding R, XAvoid this
LAvoid this
and XAvoid this
CAvoid this
directly. The impedance is the square root of RAvoid this
1 / 4Next ▶
Avoid these mistakes
2Avoid this
+ (XAvoid this
− XAvoid this
)Avoid this
, so the reactances subtract before they are squared.Avoid this
Using millihenries or microfarads in the formulas without converting them to henries and farads.Avoid this
◀ Previous2 / 4Next ▶
Avoid these mistakes
3Avoid this
Thinking that resonance means large reactances.Avoid this
At resonance the reactances are equal and cancel, so the impedance is at its smallest value, equal to R.Avoid this
4Avoid this
Mixing up peak and rms values when calculating power, for example using the peak current directly in P = IAvoid this
R without the factor of one-half.Avoid this
◀ Previous3 / 4Next ▶
Avoid these mistakes
5Avoid this
Assuming the inductor or capacitor dissipates energy.Avoid this
Only the resistor dissipates energy; the other two elements store it and return it to the circuit.Avoid this
6Avoid this
Reading the power factor as the phase angle.Avoid this
The power factor is cos φ, so a power factor of 0.075 corresponds to a phase angle of about 85.7°, not 0.075°.Avoid this
◀ Previous4 / 4
Accepted payment methods