Curriculum
Course: College Physics for AP Courses 2e
Login

Curriculum

College Physics for AP Courses 2e

Unit 8: Linear Momentum and Collisions

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 9: Statics and Torque

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 10: Rotational Motion and Angular Momentum

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 11: Fluid Statics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 12: Fluid Dynamics and Its Biological and Medical Applications

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 13: Temperature, Kinetic Theory, and the Gas Laws

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 14: Heat and Heat Transfer Methods

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 15: Thermodynamics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 16: Oscillatory Motion and Waves

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 17: Physics of Hearing

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 18: Electric Charge and Electric Field

0/36 Dr Dabour Hub Science Diagram and Course Material

Unit 19: Electric Potential and Electric Field

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 20: Electric Current, Resistance, and Ohm's Law

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 21: Circuits and DC Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 22: Magnetism

0/48 Dr Dabour Hub Science Diagram and Course Material

Unit 23: Electromagnetic Induction, AC Circuits, and Electrical Technologies

0/52 Dr Dabour Hub Science Diagram and Course Material

Unit 25: Geometric Optics

0/32 Dr Dabour Hub Science Diagram and Course Material

Unit 26: Vision and Optical Instruments

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 27: Wave Optics

0/40 Dr Dabour Hub Science Diagram and Course Material

Unit 28: Special Relativity

0/28 Dr Dabour Hub Science Diagram and Course Material

Unit 29: Quantum Physics

0/35 Dr Dabour Hub Science Diagram and Course Material
Text lesson

21.1 Resistors in Series and Parallel

21.1 Resistors in Series and Parallel — COLLEGE PHYSICS FOR AP COURSES notes: You will be able to draw series and parallel resistor circuits, calculate the total resistance, current, voltage drop and power for each resistor, and explain why a parallel combination has less resistance than its smallest branch.

1Learning objectives2Learning objectives
Learning objectives
Learning objectives
By the end of this section, you will be able to:
1
Draw a circuit with resistors in parallel and in series.
2
Calculate the voltage drop of a current across a resistor using Ohm’s law.
3
1 / 2Next ▶
Learning objectives
1

Contrast the way total resistance is calculated for resistors in series and in parallel.
2

4
3

Explain why the total resistance of a parallel circuit is less than the smallest resistance of any of the resistors in that circuit.
4

5
5

Calculate the total resistance of a circuit that contains a mixture of resistors connected in series and in parallel.
◀ Previous2 / 2
1Why resistors are combined2Why resistors are combined
Why resistors are combined
Why resistors are combined
Most circuits contain more than one component called a resistor.
A resistor limits the flow of charge in the circuit, and this limit is called resistance, measured in ohms (Ω).
The two simplest ways to connect resistors are in series and in parallel.
The total resistance of a combination depends both on the individual resistances and on how the resistors are connected.
The figure below shows a series connection (a) and a parallel connection (b) of four resistors.
1 / 2Next ▶
A series connection places resistors one after another in a single path, while a parallel connection places each resistor directly across the same two wires. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Why resistors are combined
Why resistors are combined: A series connection places resistors one after another in a single path, while a parallel connection places each resistor directly across the same two wires." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Why resistors are combined
Kirchhoff’s rules govern all of these circuits. The loop rule is energy conservation: the potential change around any closed loop is zero. The junction rule is charge conservation: the current entering a junction equals the current leaving it. Together they let us find currents and voltages in circuits that mix resistors, capacitors and sources.
◀ Previous2 / 2
1Resistors in series2Resistors in series3Resistors in series4Resistors in series5Major features of resistors in series:6Major features of resistors in series:
Resistors in series
1

Resistors are in series when the flow of charge

which is the current, must pass through each device one after another. For example, if current flows through a person holding a screwdriver and into the Earth, the total resistance includes the resistance of the screwdriver’s shaft, the resistance of its handle, the person’s body resistance, and the resistance of her shoes.
2

The figure below shows three resistors in series connected to a voltage source, and the single equivalent resistor that could replace them.
3

Because the current must pass through every resistor in turn, it is reasonable that the total resistance is the sum of the individual resistances.
4

This has practical consequences: a person who wants to avoid an electric shock can reduce the current by wearing high-resistance rubber-soled shoes,

while a faulty high-resistance cord to an appliance would reduce its operating current.
1 / 6Next ▶
Three resistors in series with a battery on the left, and the equivalent single series resistor on the right that draws the same current. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Resistors in series
Resistors in series: Three resistors in series with a battery on the left, and the equivalent single series resistor on the right that draws the same current." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

To check that series resistances really add, consider the voltage drop across each resistor.
2

A voltage drop is the loss of electrical potential energy as charge passes through a resistor.
3

According to Ohm’s law, the voltage drop V is equal to the current I multiplied by the resistance R, written as V = IR,

where V is in volts (V), I is the current in amperes (A),and R is the resistance in ohms (Ω).
4

Put another way, V is the voltage needed to push a current I through a resistance R.
5

For the three resistors in series, the drops are V1 = IR1, V2 = IR2 and V3 = IR3.
6

These drops must add up to the voltage output of the source, V = V1 + V2 + V3.
◀ Previous2 / 6Next ▶
Resistors in series
Resistors in series
This follows from conservation of energy: the energy supplied by the source,

which is charge times voltage, must equal the energy dissipated by the resistors,because there is no other source or destination of energy in the circuit.
The same charge passes through the source and through each resistor in a given time,

since there is nowhere in the circuit for charge to be stored or to leak away.
Substituting the individual voltages gives IRs = IR1 + IR2 + IR3

where Rs is the equivalent single series resistance.
Cancelling the current gives Rs = R1 + R2 + R3.
The same logic holds for any number of resistors

so the total resistance of a series connection is Rs = R1 + R2 + R3 + …
Since all of the current must pass through each resistor, the current experiences the resistance of each one, and series resistances simply add.
◀ Previous3 / 6Next ▶
Resistors in series
Resistors in series
Major features of resistors in series:
◀ Previous4 / 6Next ▶
Major features of resistors in series:
Major features of resistors in series:
Series resistances add: R
s
= R
1
+ R
2
◀ Previous5 / 6Next ▶
Major features of resistors in series:
Major features of resistors in series:
3
+ …
The same current flows through each resistor in series.
Individual resistors in series do not each receive the full source voltage

they divide it among themselves.
◀ Previous6 / 6
Connections: conservation laws
1

The derivations of the expressions for series and parallel resistance are based on two conservation laws.
2

The law of conservation of energy states that the total energy in a process is constant,

and the law of conservation of charge states that the total charge is constant.
3

Every result in this section,

from adding series resistances to splitting parallel currents, is a direct consequence of these two laws applied to a circuit.
1Resistors in parallel2Resistors in parallel3Resistors in parallel4Major features of resistors in parallel:5Major features of resistors in parallel:
Resistors in parallel
1

Resistors are in parallel when each one is connected directly to the voltage source by wires of negligible resistance.
2

Each resistor therefore has the full voltage of the source across it.
3

Each resistor draws the same current it would draw if it were alone on the source, as long as the source is not overloaded.
4

The headlights, radio and other devices in a car are wired in parallel

so each one receives the full battery voltage and works independently.
5

The wiring in a house or any building works the same way.
1 / 5Next ▶
Three resistors connected in parallel across a battery, with the equivalent single parallel resistor, and a house wiring panel that uses the same parallel principle. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Resistors in parallel
Resistors in parallel: Three resistors connected in parallel across a battery, with the equivalent single parallel resistor, and a house wiring panel that uses the same parallel principle." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Resistors in parallel
To find the equivalent parallel resistance, consider the currents.
Since each resistor has the full source voltage, the currents through the individual resistors are I1 = V/R1, I2 = V/R2 and I3 = V/R3.
Conservation of charge says that the total current I from the source is the sum of these branch currents, I = I1 + I2 + I3.
Substituting the expressions gives I = V(1/R1 + 1/R2 + 1/R3).
Ohm’s law for the equivalent single resistance also gives I = V/Rp.
Comparing the two expressions, the term in brackets must equal 1/Rp.
◀ Previous2 / 5Next ▶
Resistors in parallel
1

For any number of resistors in parallel, the total resistance Rp is given by 1/Rp = 1/R1 + 1/R2 + 1/R3 + …,

where each resistance is in ohms (Ω) and Rp is also in ohms.
2

The total parallel resistance is always less than the smallest of the individual resistances. When resistors are connected in parallel, more current flows from the source than would flow through any one of them alone

so the total resistance is lower.
3

Major features of resistors in parallel:
◀ Previous3 / 5Next ▶
Major features of resistors in parallel:
Major features of resistors in parallel:
Parallel resistance is found from 1/R
p
= 1/R
1
+ 1/R
2
◀ Previous4 / 5Next ▶
Major features of resistors in parallel:
Major features of resistors in parallel:
+ …, and it is smaller than any individual resistance in the combination.
Each resistor in parallel has the same full voltage of the source applied across it.
Power distribution systems use parallel connections so that many devices receive the same voltage and can operate independently.
Parallel resistors do not each carry the total current

they divide it. The branch currents add to the total current.
◀ Previous5 / 5
1Combinations of series and parallel2Combinations of series and parallel3Combinations of series and parallel
Combinations of series and parallel
1

More complex connections are often combinations of series and parallel.
2

These are common in practice, especially when wire resistance is considered: the wire resistance is in series with other resistances that are in parallel.
3

A combination of series and parallel can be reduced to a single equivalent resistance by repeatedly identifying a series part or a parallel part, replacing it with its equivalent,

and continuing until one resistance remains.
4

The method is more time-consuming than difficult.
5

The figure below shows a network of seven resistors, with each series or parallel part marked and reduced step by step.
1 / 3Next ▶
A network of seven resistors with series and parallel parts, shown being reduced step by step to one equivalent resistance. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Combinations of series and parallel
Combinations of series and parallel: A network of seven resistors with series and parallel parts, shown being reduced step by step to one equivalent resistance." loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

The simplest combination of series and parallel resistance is also the most instructive

because it appears in many applications.
2

For example, the first resistor could be the resistance of the wires from a car battery to its electrical devices,

and the two parallel branches could be the starter motor and a passenger compartment light.
3

We usually assume wire resistance is negligible

but when it is not, it has important effects, as the next example shows.
4

The circuit in the figure below is this simplest combination: a wire resistance in series with two resistors in parallel.
◀ Previous2 / 3Next ▶
A 12.0 V source drives a 1.00 Ω wire resistor in series with a 6.00 Ω and a 13.0 Ω resistor that are in parallel with each other. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Combinations of series and parallel
◀ Previous3 / 3
1Practical implications2Practical implications
Practical implications
1

Resistance in wires reduces the current and power delivered to a device.
2

If the wire resistance is relatively large, as in a worn or very long extension cord, the loss can be significant.
3

If a large current is drawn, the voltage drop in the wires can also be significant.
4

This is why the refrigerator light dims momentarily when the motor starts,

and why the passenger compartment light can dim when a car engine starts,although in the car this may also be caused by resistance inside the battery.
5

The figure below illustrates what happens. The motor has a very low resistance

so when it is switched on, a large current flows. This larger current causes a bigger voltage drop across the resistance of the wireswhich lowers the voltage across the bulb, and the bulb dims noticeably.
1 / 2Next ▶
A refrigerator motor with low resistance draws a large current, which causes a large voltage drop in the wires and dims the light bulb. Image: OpenStax, College Physics for AP Courses 2e, CC BY 4.0.
Practical implications
◀ Previous2 / 2
Check your understanding
Check your understanding
Question: Can any arbitrary combination of resistors be broken down into series and parallel combinations? Try to draw a circuit of resistors that cannot be broken down this way.
Answer: No. A common example is the bridge circuit: five resistors arranged in a diamond

where the fifth resistor connects the two middle junctions. No pair of resistors in that circuit is purely in series or purely in parallelso the series and parallel rules cannot reduce it directly. Other methods, such as Kirchhoff’s rules, are needed.
1Example 21.1 — Analysis of a series circuit2Example 21.2 — Analysis of a parallel circuit3Example 21.2 — Analysis of a parallel circuit4Example 21.3 — Combining series and parallel circuits5Example 21.3 — Combining series and parallel circuits6Example 21.3 — Combining series and parallel circuits
Example 21.1 — Analysis of a series circuit
1

A 12.0 V battery is connected to three resistors in series with R1 = 1.00 Ω, R2 = 6.00 Ω and R3 = 13.0 Ω. Find (a) the total resistance, (b) the current, (c) the voltage drop across each resistor and check that the drops add to 12.0 V, (d) the power dissipated by each resistor, and (e) the power output of the source and check that it equals the total power dissipated.
2

(a) Series resistances add: Rs = 1.00 Ω + 6.00 Ω + 13.0 Ω = 20.0 Ω.
3

(b) Ohm’s law gives I = V/Rs = 12.0 V / 20.0 Ω = 0.600 A.
4

(c) V1 = IR1 = 0.600 A × 1.00 Ω = 0.600 V

V2 = 0.600 A × 6.00 Ω = 3.60 VV3 = 0.600 A × 13.0 Ω = 7.80 V. The sum is 0.600 V + 3.60 V + 7.80 V = 12.0 V, as expected from conservation of energy.
5

(d) Power in each resistor is P = I2R (watts, W, when I is in amperes and R is in ohms). P1 = (0.600 A)2 × 1.00 Ω = 0.360 W

P2 = (0.600 A)2 × 6.00 Ω = 2.16 WP3 = (0.600 A)2 × 13.0 Ω = 4.68 W.
6

(e) The source power is P = IV = 0.600 A × 12.0 V = 7.20 W. The resistors dissipate 0.360 W + 2.16 W + 4.68 W = 7.20 W

so energy is conserved.
1 / 6Next ▶
Example 21.2 — Analysis of a parallel circuit
1

Use the same 12.0 V battery and the same three resistances (1.00 Ω, 6.00 Ω and 13.0 Ω), now connected in parallel. Find (a) the total resistance, (b) the total current, (c) the current in each resistor and check that they add to the total, (d) the power dissipated by each resistor, and (e) the source power and check that it equals the total dissipated power.
2

(a) 1/Rp = 1/1.00 Ω + 1/6.00 Ω + 1/13.0 Ω = 1.00 + 0.1667 + 0.0769 = 1.2436 Ω−1

so Rp = 0.804 Ω. This is smaller than the smallest individual resistance, 1.00 Ω.
3

(b) I = V/Rp = 12.0 V / 0.804 Ω = 14.9 A.
4

(c) Each resistor has the full 12.0 V: I1 = 12.0 V / 1.00 Ω = 12.0 A

I2 = 12.0 V / 6.00 Ω = 2.00 AI3 = 12.0 V / 13.0 Ω = 0.923 A. The sum is 12.0 A + 2.00 A + 0.923 A = 14.9 Awhich matches the total current and conservation of charge.
5

(d) Using P = V2/R with V = 12.0 V: P1 = 144 V2 / 1.00 Ω = 144 W

P2 = 144 V2 / 6.00 Ω = 24.0 WP3 = 144 V2 / 13.0 Ω = 11.1 W. Each resistor dissipates much more power in parallel than in series across the same source.
6

(e) P = IV = 14.9 A × 12.0 V = 179 W. The total dissipated power is 144 W + 24.0 W + 11.1 W = 179 W

which is consistent with conservation of energy.
◀ Previous2 / 6Next ▶
Example 21.2 — Analysis of a parallel circuit
Example 21.2 — Analysis of a parallel circuit
What the symbols mean:
P = power (W) · I = current (A) · V = potential difference (V)
◀ Previous3 / 6Next ▶
Example 21.3 — Combining series and parallel circuits
1

The 1.00 Ω resistor is the resistance of the wires feeding a parallel combination of the 6.00 Ω and 13.0 Ω resistors, all on a 12.0 V source. Find (a) the total resistance, (b) the voltage drop across the wire resistance, (c) the current through the 6.00 Ω resistor, and (d) the power dissipated by the 6.00 Ω resistor.
2

(a) The parallel pair has 1/Rp = 1/6.00 Ω + 1/13.0 Ω = 0.2436 Ω−1

so Rp = 4.11 Ω.
3

This is in series with the wire

so Rtotal = 1.00 Ω + 4.11 Ω = 5.11 Ω.
4

This lies between the pure series value (20.0 Ω) and the pure parallel value (0.804 Ω) found for the same resistors in the two previous examples.
5

(b) The full current flows through the wire.
6

The total current is I = V/Rtotal = 12.0 V / 5.11 Ω = 2.35 A.
◀ Previous4 / 6Next ▶
Example 21.3 — Combining series and parallel circuits
Example 21.3 — Combining series and parallel circuits
The wire voltage drop is V1 = IR1 = 2.35 A × 1.00 Ω = 2.35 V.
The voltage across the parallel pair is therefore less than the source voltage by this amount.
(c) The voltage across the parallel pair is Vp = 12.0 V − 2.35 V = 9.65 V.
The current through the 6.00 Ω resistor is I2 = Vp / 6.00 Ω = 9.65 V / 6.00 Ω = 1.61 A.
This is less than the 2.00 A that flowed through the same resistor when it was connected directly across the 12.0 V battery in Example 21.2.

(Check: the 13.0 Ω branch carries 9.65 V / 13.0 Ω = 0.742 A, and 1.61 A + 0.742 A = 2.35 A.)
(d) The power in the 6.00 Ω resistor is P = VpI2 = 9.65 V × 1.61 A = 15.5 W. This is less than the 24.0 W it dissipated when connected directly across the 12.0 V source

because the wire resistance reduces the voltage applied to it.
◀ Previous5 / 6Next ▶
Example 21.3 — Combining series and parallel circuits
Example 21.3 — Combining series and parallel circuits
Practical note: Wire resistance reduces the current and power delivered to a device. Large wire resistance, as in a worn or very long extension cord, can make this loss significant, and a large current produces a large voltage drop in the wires.
◀ Previous6 / 6
Key terms
Term Meaning
Resistor A component in a circuit that limits the flow of charge.
Resistance The measure of how strongly a device or material limits the flow of charge, measured in ohms (Ω).
Series connection An arrangement in which the current must pass through each device one after another, so there is only one path for the current.
Parallel connection An arrangement in which each device is connected directly across the same two points, so each device has the same voltage.
Current The flow of electric charge through a circuit, measured in amperes (A).
Voltage drop The loss of electric potential energy as charge passes through a resistor, measured in volts (V).
Ohm’s law The relationship V = IR, which gives the voltage drop across a resistor from the current through it and its resistance.
Equivalent series resistance The single resistance Rs = R1 + R2 + … that can replace resistors in series without changing the current.
Equivalent parallel resistance The single resistance Rp that satisfies 1/Rp = 1/R1 + 1/R2 + … and can replace parallel resistors.
Conservation of energy The principle that the total energy in an isolated process stays constant; in circuits it means the source energy equals the energy dissipated by resistors.
Conservation of charge The principle that electric charge is neither created nor destroyed; in circuits it means current entering a junction equals current leaving it.
Electric power The rate at which electric energy is transferred or dissipated, measured in watts (W).
Joule’s law The relationship P = IV between power, current and voltage in a DC circuit.
Combination of series and parallel A circuit containing both series and parallel parts that can be reduced step by step to a single equivalent resistance.
Wire resistance The resistance of the connecting wires, which is usually negligible but can be in series with other resistances and affect the circuit.
1Avoid these mistakes2Avoid these mistakes3Avoid these mistakes
Avoid these mistakes
1Avoid this
Adding parallel resistances directly.Avoid this
Parallel resistors combine by adding reciprocals (1/Rp = 1/R1 + 1/R2 + …), not by adding the resistances themselves.Avoid this
2Avoid this
Thinking the parallel resistance is larger than the smallest branch.Avoid this
The total parallel resistance is always smaller than the smallest individual resistance.Avoid this
1 / 3Next ▶
Avoid these mistakes
3Avoid this
Giving each resistor in series the full source voltage.Avoid this
In a series circuit the voltage divides among the resistors, and the drops add up to the source voltage.Avoid this
4Avoid this
Assuming each parallel branch carries the total current. The total current splits between the branches, and the branch currents add to the total.Avoid this
5Avoid this
◀ Previous2 / 3Next ▶
Avoid these mistakes
Forgetting the wire resistance in a combined circuit.Avoid this
When a wire is in series with parallel resistors, its voltage drop must be subtracted from the source voltage before finding the current in the parallel part.Avoid this
6Avoid this
Mixing up power formulas.Avoid this
Use P = I2R for a series current, P = V2/R for a parallel voltage, and P = IV for the source, and check that the units are watts.Avoid this
◀ Previous3 / 3
Accepted payment methods