Curriculum
Course: OCR A Level Physics A H556
Login

Curriculum

OCR A Level Physics A H556

1. Development of Practical Skills in Physics

0/56 Dr Dabour Hub Science Diagram and Course Material

2. Foundations in Physics

0/29 Dr Dabour Hub Science Diagram and Course Material

3. Forces and Motion

0/108 Dr Dabour Hub Science Diagram and Course Material

4. Electrons, Waves and Photons

0/71 Dr Dabour Hub Science Diagram and Course Material
Text lesson

4.6.2 Calculating Frequency

4.6.2 Calculating Frequency: Define frequency and period, use f = 1/T, and extract frequency from oscilloscope traces and time measurements.

1Frequency and Period2Frequency · Period · Relationship3Units4Units
Frequency and Period
4.6.2 Calculating Frequency" loading= - Dr Khaled Dabour Academy⤢ Enlarge
Frequency and Period
Frequency and period describe the same repetition, one counting cycles and the other timing them.
1 / 4Next ▶
Frequency · Period · Relationship
Frequency
The number of complete oscillations (or waves passing a point) each second, measured in hertz.
Period
The time taken for one complete oscillation, measured in seconds.
Relationship
f = 1/T

so a short period means a high frequency and vice versa.
◀ Previous2 / 4Next ▶
Units
Units
One hertz is one cycle per second, and prefixes such as kHz (103 Hz) and MHz (106 Hz) are common.
On an oscilloscope, the horizontal axis is the time-base and the vertical axis shows voltage.
A time-base may be given per millimetre

so a division measured in centimetres must be converted before finding the period.
Use as many complete wavelengths as possible on the screen, since this reduces the uncertainty in the measured period.
Dividing the total time across the trace by the number of wavelengths shown gives the period in seconds.
◀ Previous3 / 4Next ▶
Two waves of equal height, the upper one with more cycles and higher frequency.
Units
◀ Previous4 / 4
1Finding Frequency From Data2Finding Frequency From Data
Finding Frequency From Data
1

1
2

To find the period from a displacement-time graph, read the time between two successive identical points, such as peaks.
3

2
4

On an oscilloscope, multiply the number of horizontal divisions for one cycle by the time-base setting to get the period.
5

3
6

Convert the period to seconds before using f = 1/T, since milliseconds and microseconds give wrong values otherwise.
1 / 2Next ▶
Finding Frequency From Data
1

4
2

Alternatively count N cycles in a measured time t, and use f = N/t

which reduces timing uncertainty.
3

5
4

Quote the frequency in suitable units and check that it is reasonable for the type of wave.
◀ Previous2 / 2
Examples of Typical Frequencies
Examples of Typical Frequencies
UK mains alternates at 50 Hz

so the period is 0.020 s.
Human hearing covers about 20 Hz to 20 kHz, with middle of the range near 1 kHz.
FM broadcasts are around 100 MHz

which is 1 × 108 Hz.
Frequencies lie near 1014 Hz

which is far too fast to count directly.
Worked Example
1

Question: On an oscilloscope with a time-base of 2.0 ms per division, one complete cycle of a signal spans 5.0 divisions. Calculate the period and frequency.
2

Period T = 5.0 divisions × 2.0 ms per division = 10 ms = 0.010 s.
3

Frequency f = 1/T = 1⁄0.010 = 100 Hz.
4

Answer: T = 0.010 s and f = 100 Hz.
14.6.2 – Main ideas for the Exam2Common Mistakes
4.6.2 – Main ideas for the Exam
4.6.2 – Main ideas for the Exam
Frequency: The number of oscillations per second, in hertz.
Period: The time for one complete oscillation, in seconds.
Hertz: The SI unit of frequency, equal to one cycle per second.
Oscilloscope: An instrument that displays how a voltage varies with time.
1 / 2Next ▶
Common Mistakes
Common Mistakes
Using milliseconds directly in f = 1/T without converting to seconds.
Reading the period from a crest to a trough instead of from crest to crest.
Forgetting that frequency is set by the source and does not change when a wave changes medium.
Confusing hertz with a measurement of speed.
◀ Previous2 / 2
Accepted payment methods