Curriculum
Course: OCR A Level Physics A H556
Login

Curriculum

OCR A Level Physics A H556

1. Development of Practical Skills in Physics

0/56 Dr Dabour Hub Science Diagram and Course Material

2. Foundations in Physics

0/29 Dr Dabour Hub Science Diagram and Course Material

3. Forces and Motion

0/108 Dr Dabour Hub Science Diagram and Course Material

4. Electrons, Waves and Photons

0/71 Dr Dabour Hub Science Diagram and Course Material
Text lesson

4.5.2 Variable Resistance Components

4.5.2 Variable Resistance Components: Describe how the resistance of an LDR, a thermistor and a variable resistor changes, and use them in potential divider circuits as sensors.

1Light-Dependent Resistor2Behaviour · Cause · Use3Graph
Light-Dependent Resistor
4.5.2 Variable Resistance Components" loading= - Dr Khaled Dabour Academy⤢ Enlarge
Light-Dependent Resistor
Sensors change resistance with their surroundings, allowing a divider’s output to depend on conditions.
1 / 3Next ▶
Behaviour · Cause · Use
Behaviour
The resistance of an LDR is large in darkness and falls as the light intensity on it increases.
Cause
Light frees more charge carriers in the semiconductor material

so more current flows for the same p.d.
Use
LDRs sense brightness in circuits for automatic street lights, alarms and camera exposure.
◀ Previous2 / 3Next ▶
Graph
Graph
The resistance against intensity graph falls steeply at first and then flattens

so the relationship is not linear.
◀ Previous3 / 3
1Thermistor2Thermistor
Thermistor
Thermistor
The common thermistor has a negative temperature coefficient

so its resistance falls as temperature increases.
Heating releases more charge carriers in the semiconductor

which outweighs the extra lattice vibrations.
Thermistors measure and control temperature in thermostats, fire alarms and digital thermometers.
A metal wire behaves oppositely: its resistance increases with temperature.
The same current flows through a sensor and a fixed resistor in series

so the p.d. across each is proportional to its resistance.
A thermistor circuit can switch a heater off automatically when its surroundings reach room temperature.
1 / 2Next ▶
Graph of thermistor resistance in kΩ against temperature in °C, a decreasing curve from 33.7 kΩ at 0 °C to 0.7 kΩ at 100 °C
Thermistor
Graph of thermistor resistance in kΩ against temperature in °C, a decreasing curve from 33.7 kΩ at 0 °C to 0.7 kΩ at 100 °C" loading= - Dr Khaled Dabour Academy⤢ Enlarge
1

An LDR is a non-ohmic device

so its resistance is not constant and it does not obey Ohm’s law.
2

A calibration curve of output p.d. against light intensity can be used to find an unknown light intensity from a measured voltage.
3

Thermistor circuits are also used in ovens.
◀ Previous2 / 2
1Sensors in Dividers2Sensors in Dividers3Sensors in Dividers
Sensors in Dividers
1

1
2

Place the sensor and a fixed resistor in series across a supply to form a potential divider.
3

2
4

A change in light or temperature alters the sensor’s resistance

which changes the ratio in which the p.d. is shared.
5

3
6

With the output taken across the LDR, the output rises in darkness because the LDR then takes a larger share of the supply.
1 / 3Next ▶
Sensors in Dividers
Sensors in Dividers
4
With the output across the fixed resistor, the output rises in bright conditions as more of the p.d. is left for it.
5
Choose the fixed resistor close to the sensor’s resistance at the switching point to get the best sensitivity.
Component Controlled by Resistance trend
LDR Light intensity Falls as light increases
NTC thermistor Temperature Falls as temperature rises
Variable resistor Manual adjustment Set by the user
◀ Previous2 / 3Next ▶
Potential divider: cell, resistor R1 and resistor R2 in series in one loop, with a voltmeter across R2 giving Vout
Sensors in Dividers
◀ Previous3 / 3
Worked Example
Worked Example
Question: A 6.0 V supply is connected across a 2.0 kΩ fixed resistor in series with a thermistor. The output is taken across the thermistor. Find the output when the thermistor resistance is 4.0 kΩ and when it falls to 1.0 kΩ.
At 4.0 kΩ: Vout = 6.0 × 4.0 / (2.0 + 4.0) = 4.0 V.
At 1.0 kΩ: Vout = 6.0 × 1.0 / (2.0 + 1.0) = 2.0 V.
As the temperature rises the resistance falls

so the output across the thermistor falls.
Answer: 4.0 V at 4.0 kΩ and 2.0 V at 1.0 kΩ.
14.5.2 – Main ideas for the Exam2Common Mistakes
4.5.2 – Main ideas for the Exam
4.5.2 – Main ideas for the Exam
LDR: A light-dependent resistor whose resistance falls as light intensity rises.
Thermistor: A resistor whose resistance varies with temperature

NTC types fall as temperature rises.
Sensor: A component producing a changing p.d. or resistance in response to a physical condition.
Variable resistor: A resistor with a resistance that can be altered by hand.
1 / 2Next ▶
Common Mistakes
1

Stating that thermistor resistance rises with temperature

which is the opposite of an NTC thermistor.
2

Forgetting which component the output is taken across

so the trend is reversed.
3

Saying an LDR’s resistance is zero in bright light

it is small but not zero.
4

Assuming the LDR and thermistor graphs are straight lines.
◀ Previous2 / 2
Accepted payment methods