Curriculum
Course: OCR A Level Physics A H556
Login

Curriculum

OCR A Level Physics A H556

1. Development of Practical Skills in Physics

0/56 Dr Dabour Hub Science Diagram and Course Material

2. Foundations in Physics

0/29 Dr Dabour Hub Science Diagram and Course Material

3. Forces and Motion

0/108 Dr Dabour Hub Science Diagram and Course Material

4. Electrons, Waves and Photons

0/71 Dr Dabour Hub Science Diagram and Course Material
Text lesson

3.7.6 Young’s Modulus

3.7.6 Young’s Modulus — OCR A Level Physics A notes: Define and calculate Young’s modulus and describe how to measure it for a wire.

1Definition2Definition3Definition
Definition
Definition
For the region where stress is proportional to strain, the ratio is a constant of the material called the Young modulus: E = stress / strain = (F/A) / (Δl/l) = Fl / AΔl.
1 / 3Next ▶
Definition
1

Its unit is the pascal (Pa), the same as stress because strain has no unit

typical values for metals are of the order 10
2

11
3

Pa (steel about 2.0 × 10
4

Pa, copper about 1.2 × 10
5

Pa),
6

and for rubber near 107 Pa.
◀ Previous2 / 3Next ▶
Wire under tension with extension measured, and a stress-strain graph for the Young modulus
Definition
Wire under tension with extension measured, and a stress-strain graph for the Young modulus" loading= - Dr Khaled Dabour Academy⤢ Enlarge
Definition
A high value means a stiff material that undergoes little strain for a given stress.
Unlike the force constant k, E is independent of the sample’s length and area

so it is a property of the material. The two are linked by k = EA / l: a wire is stiffer when it is thicker (larger A), shorter (smaller l) or made of stiffer material.
◀ Previous3 / 3
1On the stress–strain graph2On the stress–strain graph
On the stress–strain graph
On the stress–strain graph
The gradient of the straight (Hookean) part of a stress–strain graph equals the Young modulus.
1 / 2Next ▶
On the stress–strain graph
1

If the graph is a force–extension graph, the gradient is k = F/Δl, and the Young modulus is found from E = (gradient × l) / A.
2

The area under a stress–strain graph is energy per unit volume

so the energy stored in a stretched wire is E
3

el
4

= ½ × stress × strain × volume = ½FΔl.
◀ Previous2 / 2
1Experiment: Young modulus of a wire2Experiment: Young modulus of a wire
Experiment: Young modulus of a wire
1

A long thin wire (about 2 m of copper or constantan) is clamped at one end, passes over a pulley, and carries a hanging mass holder. A reference marker (a strip of tape) is attached near the load and a metre rule fixed beside it, or a travelling microscope or vernier is used to read the extension. Method:
2

1
3

Measure the original length l from the fixed clamp to the marker with a metre rule (uncertainty about ±1 mm on 2 m is small).
4

2
5

Measure the diameter of the wire at several points along the length and in perpendicular directions with a micrometer, and average.
6

The area A = πd2/4.
1 / 2Next ▶
Experiment: Young modulus of a wire
Experiment: Young modulus of a wire
3
Add a small initial load to straighten the wire

then add masses in equal steps, recording the extension each time.
Also unload, checking that the wire returns to its original length.
4
Plot force F (or stress) against extension (or strain). The gradient is F/Δl

so E = gradient × l / A.
The diameter is the biggest source of uncertainty since A depends on d2: a 2% error in d gives a 4% error in A. Safety: wear goggles and keep feet clear because a breaking wire can whip, and cushion the floor beneath the masses.
◀ Previous2 / 2
Why E is a useful quantity
1

Engineers use E to predict deflection of beams, stretch of cables and to choose materials for stiffness. At atomic level E is related to the slope of the force–separation curve at equilibrium spacing: stronger bonds produce a larger E. Composite materials such as carbon fibre combine high E with low density

so are used where stiffness-to-weight is key.
2

The ultimate tensile stress is the largest stress a wire can take before it breaks.
3

Beyond the elastic limit a wire deforms plastically and keeps a permanent extension once unloaded.
4

Reading the metre rule at eye level reduces parallax error, and a set square keeps the ruler straight.
5

Readings should be taken only when the wire is stationary, and repeated runs should be averaged.
1Worked strategy and links2Worked strategy and links
Worked strategy and links
Worked strategy and links
When asked for the Young modulus, first find the area from the diameter

then the stressthen the strainthen divide, keeping units in SI throughout.
1
If a graph is supplied, find the gradient using a large triangle.
2
Link to energy: the energy stored per unit volume in a stretched wire equals ½ × stress × strain,
so a material with a high E can store energy only with a high stress.
1 / 2Next ▶
Worked strategy and links
Worked strategy and links
3
Link also to 3.7.1: k = EA/l shows how a wire’s stiffness depends on both the material and its geometry.
4
In evaluation answers, note that using a longer wire gives a larger extension and smaller percentage uncertainty in the extension.
◀ Previous2 / 2
1Worked examples2Worked examples
Worked examples
1

Worked example 1. A steel wire 2.5 m long with diameter 0.60 mm carries a load of 80 N and extends 4.2 mm. Find the Young modulus.
2

A = π(0.60 × 10−3)2/4 = 2.83 × 10−7 m2.
3

Stress = 80⁄2.83 × 10−7 = 2.83 × 108 Pa. Strain = 4.2 × 10−3/2.5 = 1.68 × 10−3.
4

E = 2.83 × 108/1.68 × 10−3 = 1.7 × 1011 Pa.
5

Worked example 2. A wire has k = 600 N m−1, length 1.8 m and area 1.0 × 10−7 m2. Find its Young modulus.
6

E = kl/A = 600 × 1.8 / 1.0 × 10−7 = 1.1 × 1010 Pa.
1 / 2Next ▶
Worked examples
1

Worked example 3. A copper wire (E = 1.2 × 1011 Pa) of length 3.0 m and cross-section 1.5 × 10−6 m2 carries a force of 90 N. Find the extension and the energy stored.
2

Δl = Fl/(AE) = 90 × 3.0/(1.5 × 10−6 × 1.2 × 1011) = 270⁄1.8 × 105 = 1.5 × 10−3 m.
3

Energy = ½FΔl = 0.5 × 90 × 1.5 × 10−3 = 0.068 J.
◀ Previous2 / 2
Key terms
Term Meaning
Young modulus Ratio of stress to strain in the linear region, in Pa.
Stiffness Resistance to deformation, high E means stiff.
Micrometer Instrument to measure wire diameter to ±0.01 mm.
Gradient Slope of a graph; here gives F/Δl or E.
Hookean region Region where stress is proportional to strain.
Energy density Energy stored per unit volume, ½ × stress × strain.
1Avoid these mistakes2Avoid these mistakes
Avoid these mistakes
1Avoid this
Quoting the unit of E as N or N m. It is Pa (N m−2).Avoid this
2Avoid this
Using the diameter in place of the area, or radius in place of the diameter, in the area formula.Avoid this
3Avoid this
Using the extended length in strain instead of the original length.Avoid this
1 / 2Next ▶
Avoid these mistakes
4Avoid this
Taking the gradient of a graph with extension on the y-axis and force on the x-axis as k.Avoid this
5Avoid this
Using non-linear region data to determine E.Avoid this
◀ Previous2 / 2
Accepted payment methods