Curriculum
Course: OCR A Level Physics A H556
Login

Curriculum

OCR A Level Physics A H556

1. Development of Practical Skills in Physics

0/56 Dr Dabour Hub Science Diagram and Course Material

2. Foundations in Physics

0/29 Dr Dabour Hub Science Diagram and Course Material

3. Forces and Motion

0/108 Dr Dabour Hub Science Diagram and Course Material

4. Electrons, Waves and Photons

0/71 Dr Dabour Hub Science Diagram and Course Material
Text lesson

1.1.2 Control Variables

1.1.2 Control Variables — OCR A Level Physics A notes: Identify the variables that must be controlled in an experiment and describe practical ways of keeping them constant.

Why control variables matter
Why control variables matter
A fair test changes only one quantity at a time. If two quantities change together, a change in the result cannot be assigned to either, and the experiment is not valid. Variables that you do not want to influence the result are called control variables, and a good plan lists them and explains how each is kept constant.
The first step is to ask, from the physics

which quantities appear in the relevant equation or could physically affect the outcome. For the resistance of a wire, R = ρL/A: if you vary L, you must keep the material, the cross-sectional area and the temperature fixed.
1Common control variables and how to control them2Common control variables and how to control them3Common control variables and how to control them
Common control variables and how to control them
1

Temperature
2

use a low current and switch off between readings so a wire does not heat up

for thermal experiments use a water bath and stirrer, or a lagged container.
3

Mass
4

use the same trolley or add equal masses to each side

check with a balance.
5

Amplitude or starting position
6

release from the same mark each time, or use a fixed release height.
1 / 3Next ▶
Common control variables and how to control them
Common control variables and how to control them
Material and dimensions
use samples cut from the same reel

measure diameters with a micrometer at several places.
Voltage or current
use a stabilised supply or a variable resistor with an ammeter to hold the current at a set value.
Environment
ambient light level, draughts, background radiation (measured and subtracted).
◀ Previous2 / 3Next ▶
Cross-section of a polystyrene calorimetry cup with lid, thermometer and stirrer, inside a glass beaker with an air gap.
Common control variables and how to control them
◀ Previous3 / 3
1Variables that cannot be fully controlled2Variables that cannot be fully controlled
Variables that cannot be fully controlled
Variables that cannot be fully controlled
Some factors cannot be held perfectly constant.
1 / 2Next ▶
Variables that cannot be fully controlled
1

Room temperature drifts, a battery slowly runs down, and a human reaction time changes.
2

The plan should say how the effect is minimised or monitored: record the temperature at the start and end

use a mains power supply instead of a batteryuse light gates instead of a stopwatch.
3

Where a variable cannot be controlled, it should be measured so that its possible influence can be commented on in the evaluation.
4

A control variable is sometimes confused with a control experiment. A control experiment is a separate run in which the independent variable is not applied

giving a baseline for comparison. An example is measuring the count rate with no source presentwhich is the background count rate.
◀ Previous2 / 2
Variable resistor symbol with arrow in series with a lamp and battery.
Controlling several variables in one investigation
Variable resistor symbol with arrow in series with a lamp and battery." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Controlling several variables in one investigation
Many A Level experiments investigate two relationships in turn. To study how the terminal velocity of a ball bearing in oil depends on radius and on temperature, you would run one series varying radius at constant temperature, and a second varying temperature with the same ball. For each series, the other variable is a control variable.
If the plan involves a graph, linking the control variables to the gradient is useful: the gradient is only meaningful if everything it depends on has been held constant during the series.
Linking to uncertainty
1

Imperfect control adds to scatter in the data. If repeated readings at the same setting differ more than the instrument resolution suggests, an uncontrolled variable is often responsible. This is a clue to look for in the evaluation of an experiment (see 1.2.4 and 1.2.9).
2

Preliminary studies are needed to find extra variables that affect an experiment and the best way to control each one.
3

An experiment planned without preliminary research is likely to be invalid

because other influencing variables go unidentified.
4

In Charles’s law, temperature is the independent variable

so pressure and the amount of gas must stay fixed.
5

In Boyle’s law, pressure is varied while temperature and the number of moles stay constant to keep results reliable.
1Spotting the hidden variable2Spotting the hidden variable3Spotting the hidden variable
Spotting the hidden variable
Spotting the hidden variable
A skill that is often tested is spotting a variable that the student has not realised is changing.
1
In an investigation of the cooling of hot water, using a larger volume in one beaker changes the surface area and the mass at the same time

using a different thermometer depth changes the temperature reading.
2
In a light experiment, the brightness of the room, the distance from the source and the angle of the detector may all influence a light-dependent resistor.
3
1 / 3Next ▶
Spotting the hidden variable
Spotting the hidden variable
A useful habit is to write the equation that links the quantities and check every symbol on the right-hand side.
4
Any symbol that is not the independent variable must either be constant or be measured.
5
If the equation is not known, ask what physical processes could change the result and treat each as a potential control variable.
6
◀ Previous2 / 3Next ▶
Spotting the hidden variable
Spotting the hidden variable
Finally, remember that a controlled variable should be controlled for the whole experiment, not just at the beginning.
◀ Previous3 / 3
Worked examples
1

Worked example 1. A student investigates how the time t for a metal ball to fall a fixed distance through a viscous liquid depends on the ball’s diameter d. State four control variables and how each is controlled.
2

1. Liquid temperature: use the same liquid, left in the room, and check with a thermometer before each drop.
2. Fall distance: fix two marks on the tube, and measure with a metre rule.
3. Density of the ball: use balls of the same material.
4. Release point: drop each ball from just below the surface at the centre of the tube.
3

Only d is changed (measured with a micrometer).
4

Worked example 2. In an experiment on the resistance of a wire, the student leaves the current switched on throughout and finds the resistance for the longer lengths is larger than expected. Suggest why and what to do.
5

The current heats the wire

resistance of a metal increases with temperaturewhich is an uncontrolled variable. Use a smaller current, and switch off between readings so the wire returns to room temperature.
6

Check by repeating one length after a rest: the resistance should return to the original value.
Key terms
Term Meaning
Control variable A variable kept constant so only the independent variable affects the result.
Control experiment A run without the independent variable applied, giving a baseline.
Fair test One in which only the independent variable changes.
Background count Radiation detected with no source present, to be subtracted.
Lagging Insulation used to reduce thermal energy transfer.
1Avoid these mistakes2Avoid these mistakes
Avoid these mistakes
1Avoid this
Listing control variables but not explaining how they are kept constant.Avoid this
2Avoid this
Confusing a control variable with the dependent variable or with a control experiment.Avoid this
3Avoid this
Forgetting temperature as a control variable in electrical and thermal experiments.Avoid this
1 / 2Next ▶
Avoid these mistakes
4Avoid this
Assuming a variable is controlled because it was constant in theory, without checking it with an instrument.Avoid this
5Avoid this
Changing two variables at once to save time.Avoid this
◀ Previous2 / 2
Accepted payment methods