Curriculum
Course: AQA A Level Physics 7408
Login

Curriculum

AQA A Level Physics 7408

2. Particles and Radiation

0/58 Dr Dabour Hub Science Diagram and Course Material

3. Waves

0/39 Dr Dabour Hub Science Diagram and Course Material

4. Mechanics and Materials

0/77 Dr Dabour Hub Science Diagram and Course Material

5. Electricity

0/25 Dr Dabour Hub Science Diagram and Course Material

6. Further Mechanics and Thermal Physics

0/77 Dr Dabour Hub Science Diagram and Course Material

7. Fields and Their Consequences

0/111 Dr Dabour Hub Science Diagram and Course Material

8. Nuclear Physics

0/56 Dr Dabour Hub Science Diagram and Course Material

9. Astrophysics

0/65 Dr Dabour Hub Science Diagram and Course Material

10. Medical Physics

0/64 Dr Dabour Hub Science Diagram and Course Material

11. Engineering Physics

0/46 Dr Dabour Hub Science Diagram and Course Material

12. Turning Points in Physics

0/56 Dr Dabour Hub Science Diagram and Course Material
Text lesson

11.2.8 Engine Efficiency

11.2.8 Engine Efficiency — AQA A Level Physics 7408 notes: Calculate thermal and overall efficiency of engines and use the temperature limit on efficiency.

1Defining efficiency2Thermal efficiency3Thermal efficiency4Overall efficiency
Defining efficiency
Defining efficiency
Efficiency compares what we want with what we pay for. For any device, efficiency = useful energy (or power) output ÷ total energy (or power) input, usually written as a fraction or a percentage. For an engine it has to be stated carefully because there are several stages.
1 / 4Next ▶
Thermal efficiency
1

net work per cycle ÷ heat supplied per cycle = W/Q
2

in
3

= (Q
4

− Q
5

out
◀ Previous2 / 4Next ▶
Thermal efficiency
Thermal efficiency
)/Q
.
It takes only the gas cycle into account and can be found from the p–V loop.
◀ Previous3 / 4Next ▶
Sankey diagram of an electric motor: 500 J electrical energy in, 120 J useful out to the right, 380 J wasted downward.
Overall efficiency
Sankey diagram of an electric motor: 500 J electrical energy in, 120 J useful out to the right, 380 J wasted downward." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Overall efficiency
brake power ÷ fuel power input. It also includes friction and other losses

so it is lower than the thermal efficiency.
◀ Previous4 / 4
Fuel power
1

The energy input comes from the fuel. The fuel power is the calorific value (energy released per kilogram of fuel, J kg−1) multiplied by the mass of fuel burnt per second:
2

input power = calorific value × fuel mass flow rate
3

For a fuel quoted in energy per litre, multiply by the volume used per second. A typical liquid fuel has a calorific value of around 4.5 × 107 J kg−1.
1The theoretical limit2The theoretical limit3The theoretical limit
The theoretical limit
1

No heat engine can convert all of Qin into work (see 11.2.9). The maximum possible thermal efficiency between a hot source at temperature TH and a cold sink at TC (both in kelvin) is
2

efficiencymax = (TH − TC)/TH = 1 − TC/TH
3

This is the efficiency of an ideal reversible (Carnot) engine.
1 / 3Next ▶
The theoretical limit
The theoretical limit
It shows that you can improve efficiency by raising T
H
or lowering T
C
, and that it is always below 100 % because T
cannot be zero.
◀ Previous2 / 3Next ▶
The theoretical limit
1

It is the reason why high compression ratios (higher peak temperatures) give better efficiency.
2

Real engines come well below this limit.
◀ Previous3 / 3
1Improving efficiency2Improving efficiency3Improving efficiency
Improving efficiency
Improving efficiency
1
Raise the peak temperature, within limits set by materials and by knock or NO
x
formation.
2
Reduce friction with lubricants and better bearings.
1 / 3Next ▶
Improving efficiency
Improving efficiency
3
Reduce heat loss through the cylinder walls with ceramic or insulating parts.
4
Use waste heat, for example in turbochargers, combined heat and power systems or combined-cycle power stations.
5
Burn the fuel completely with correct mixture and timing.
◀ Previous2 / 3Next ▶
Improving efficiency
Improving efficiency
The last point shows that efficiency is both a thermodynamic and an engineering matter.
◀ Previous3 / 3
1Energy accounting for a whole vehicle2Energy accounting for a whole vehicle3Energy accounting for a whole vehicle4Energy accounting for a whole vehicle
Energy accounting for a whole vehicle
Energy accounting for a whole vehicle
Overall efficiency of an engine is only part of the story.
1 / 4Next ▶
Energy accounting for a whole vehicle
Energy accounting for a whole vehicle
For a vehicle the fuel energy passes through the engine (about 30 % efficient), the gearbox and transmission (about 90 %) and finally into the motion of the car,
where it is lost to air resistance, rolling resistance and braking.
A chain of efficiency stages multiplies: 0.30 × 0.90 = 0.27,
so only about 27 % of the fuel energy reaches the wheels, and less still is useful in a stop-start journey.
You can also use efficiency to compare running cost.
If a litre of fuel releases 3.5 × 10
◀ Previous2 / 4Next ▶
Energy accounting for a whole vehicle
1

7
2

J and the engine is 30 % efficient,
3

then each litre supplies 1.05 × 107 J of useful work

at a steady resistive force of 700 N, this carries the car a distance of 1.05 × 107/700 = 15 000 m,or 15 km per litre.
4

Such calculations come up in questions linking engines to forces and work done.
◀ Previous3 / 4Next ▶
Three devices in series with energy arrows between them (100 J, 80 J, 48 J, 43.2 J) and downward wasted-energy arrows at each device.
Energy accounting for a whole vehicle
◀ Previous4 / 4
Quick revision summary
Quick revision summary
Keep the three kinds of efficiency separate: thermal (W/Qin), overall (BP/fuel power) and the Carnot limit (1 − TC/TH, in kelvin). Fuel power is calorific value times mass flow rate. A quoted efficiency must be less than the Carnot limit for the same temperatures.
1Worked examples2Worked examples
Worked examples
1

Worked example 1. In a cycle 1500 J of heat is supplied and 1050 J is rejected. Find the thermal efficiency.
2

W = 1500 − 1050 = 450 J. Efficiency = 450/1500 = 0.30 (30 %).
3

Worked example 2. An engine operates between a gas at 900 K and surroundings at 300 K. Find the maximum possible efficiency. If it actually produces 25 kJ of work from 100 kJ of heat, compare.
4

Max = 1 − 300⁄900 = 1 − 0.333 = 0.67 (67 %).
5

Actual = 25⁄100 = 25 %

which is about 37 % of the theoretical maximum.
6

Worked example 3. A diesel engine delivers 30 kW brake power while burning 2.0 × 10−3 kg s−1 of fuel of calorific value 4.5 × 107 J kg−1. Find the overall efficiency.
1 / 2Next ▶
Worked examples
1

Fuel power = 4.5 × 107 × 2.0 × 10−3 = 9.0 × 104 W = 90 kW.
2

Efficiency = 30⁄90 = 0.33 (33 %).
◀ Previous2 / 2
Key terms
Term Meaning
Thermal efficiency Net work per cycle divided by heat input per cycle
Overall efficiency Brake power divided by fuel power
Calorific value Energy released per kilogram of fuel burnt
Carnot limit Maximum efficiency (TH − TC)/TH
Heat input Energy supplied by burning fuel per cycle
1Avoid these mistakes2Avoid these mistakes3Avoid these mistakes
Avoid these mistakes
1Avoid this
Using Celsius temperatures in the maximum efficiency equation; kelvin must be used.Avoid this
2Avoid this
Quoting efficiency above 100 % or equal to 100 % for a real engine.Avoid this
3Avoid this
Using brake power as the work per cycle in thermal efficiency, or mixing power and energy in one ratio.Avoid this
1 / 3Next ▶
Avoid these mistakes
4Avoid this
Believing the maximum efficiency depends on the working fluid; it depends only on TAvoid this
HAvoid this
and TAvoid this
CAvoid this
.Avoid this
◀ Previous2 / 3Next ▶
Avoid these mistakes
5Avoid this
Forgetting to convert fuel per hour to per second before calculating fuel power.Avoid this
◀ Previous3 / 3
Accepted payment methods