Curriculum
Course: AQA A Level Physics 7408
Login

Curriculum

AQA A Level Physics 7408

2. Particles and Radiation

0/58 Dr Dabour Hub Science Diagram and Course Material

3. Waves

0/39 Dr Dabour Hub Science Diagram and Course Material

4. Mechanics and Materials

0/77 Dr Dabour Hub Science Diagram and Course Material

5. Electricity

0/25 Dr Dabour Hub Science Diagram and Course Material

6. Further Mechanics and Thermal Physics

0/77 Dr Dabour Hub Science Diagram and Course Material

7. Fields and Their Consequences

0/111 Dr Dabour Hub Science Diagram and Course Material

8. Nuclear Physics

0/56 Dr Dabour Hub Science Diagram and Course Material

9. Astrophysics

0/65 Dr Dabour Hub Science Diagram and Course Material

10. Medical Physics

0/64 Dr Dabour Hub Science Diagram and Course Material

11. Engineering Physics

0/46 Dr Dabour Hub Science Diagram and Course Material

12. Turning Points in Physics

0/56 Dr Dabour Hub Science Diagram and Course Material
Text lesson

4.8.2 Required Practical- The Young Modulus

4.8.2 Required Practical- The Young Modulus — AQA A Level Physics 7408 notes: Plan and carry out an experiment to measure the Young modulus of a metal wire, treat the results with a graph, and evaluate uncertainties.

1Aim and idea2Aim and idea3Aim and idea
Aim and idea
Aim and idea
The aim is to determine the Young modulus of the material of a long thin metal wire by measuring how its extension depends on the tensile force.
1 / 3Next ▶
Aim and idea
1

From E = FL/(AΔx) we obtain Δx = (L/AE)F,
2

so a graph of extension Δx against force F (horizontal) is a straight line through the origin with gradient L/(AE).

(on the vertical axis)
3

Hence E = L/(A × gradient)

where L is the original length and A the cross-sectional area.
4

Alternatively, plot stress against strain, and the gradient is directly E.
◀ Previous2 / 3Next ▶
Wire under tension with extension measured, and a stress-strain graph for the Young modulus
Aim and idea
◀ Previous3 / 3
1Apparatus and set-up2Apparatus and set-up3Apparatus and set-up
Apparatus and set-up
Apparatus and set-up
1
A long thin wire (about 2 m of steel, copper or constantan) clamped firmly at one end, passing over a pulley, with a mass hanger at the free end.
A second reference wire of the same type, hung beside it, compensates for temperature changes and the sagging of the support.
2
A set of slotted masses (for example 100 g each).
3
1 / 3Next ▶
Apparatus and set-up
1

A metre rule or tape measure for the original length L.
2

4
3

A micrometer screw gauge for the wire diameter.
4

5
5

A fiducial marker (a small piece of tape) on the wire next to a fixed scale, or a vernier scale, to measure the extension.
6

6
◀ Previous2 / 3Next ▶
Apparatus and set-up
1

Safety goggles and a box of sand or foam to catch falling masses.
2

A long wire gives a larger and more measurable extension. A thin wire gives a bigger strain for the same load

which is why the wire is thin and the experiment is done with moderate load.
◀ Previous3 / 3
1Method2Method3Method
Method
Method
1
Measure the length L from the clamp to the marker with a rule. This is a source of a few mm of uncertainty, small compared with 2 m.
2
Use the micrometer to measure the wire diameter d at several places along the wire and around the circumference (at least in two perpendicular directions each),
and take the mean.
Calculate A = πd2/4.

Because A depends on d2, the percentage uncertainty in A is twice the percentage uncertainty in d, so this is usually the largest source of error.
1 / 3Next ▶
Method
1

3
2

Hang a small initial load to straighten out kinks

record the marker position as the zero for extension.
3

4
4

Add masses one at a time, recording the marker position each time. Convert mass to force with F = mg.
5

5
6

Remove the masses one by one, recording the position again, to check that the wire is still within its elastic limit (the reading should return to the starting value).
◀ Previous2 / 3Next ▶
Method
Method
6
Do not exceed the safe load, since the wire can snap and recoil.
◀ Previous3 / 3
Analysis
Analysis
Plot Δx against F, draw the best-fit line through the origin, and find its gradient using a large triangle. Then E = L/(A × gradient). To estimate the uncertainty, draw the steepest and shallowest acceptable lines and use the percentage difference in gradient, adding the percentage uncertainty in L and twice that in d.
For a typical steel wire, L = 2.0 m, d = 0.40 mm, A = 1.26 × 10−7 m2, and a gradient of 1.3 × 10−4 m N−1 gives E = 2.0/(1.26 × 10−7 × 1.3 × 10−4) = 1.2 × 1011 Pa. The value depends on the sample

for a stiff steel one would expect about 2 × 1011 Pa.
1Sources of error and improvements2Sources of error and improvements
Sources of error and improvements
1

1
2

The diameter is small

so a micrometer reading uncertainty of 0.01 mm on 0.40 mm is 2.5%which becomes 5% in A.
3

Measure at many places and use the mean.
4

2
5

Extensions are small, around a millimetre

so reading uncertainty is large relative to the signal.
6

Use a longer wire, a vernier scale, or a travelling microscope.
1 / 2Next ▶
Sources of error and improvements
1

3
2

Temperature changes alter the length. Use a reference wire.
3

4
4

Kinks and slipping at the clamp cause false extension. Use a pre-load and check that the unloading readings return to zero.
5

5
6

Stay within the limit of proportionality: the graph should remain straight.
◀ Previous2 / 2
1Safety and links2Safety and links
Safety and links
Safety and links
Wear eye protection, and keep feet clear of the masses. If a wire breaks, the stored energy (see 4.7.6) is released suddenly

so the safe loading limit matters. This practical applies the definitions of stress, strain and E from 4.7.3.
The Young modulus is the tensile stress divided by the tensile strain, and it indicates how stiff a material is.
Because strain has no units, the Young modulus is measured in pascals.
Young modulus values are typically very large, often in the order of gigapascals.
A stress-strain graph’s gradient gives the Young modulus only over the straight-line part

where Hooke’s law holds.
Energy stored per unit volume of a material is represented by the area under its linear region on a stress-strain graph.
1 / 2Next ▶
Safety and links
Safety and links
Engineers rely on the Young modulus to make sure the materials they choose can withstand the forces applied to them.
◀ Previous2 / 2
1Worked examples2Worked examples
Worked examples
Worked examples
Worked example 1. In a Young modulus experiment, the wire has length 2.20 m and mean diameter 0.35 mm. The gradient of the extension against force graph is 1.15 × 10−4 m N−1. Find E.
A = π(0.35 × 10−3)2/4 = 9.62 × 10−8 m2.
E = L/(A × gradient) = 2.20/(9.62 × 10−8 × 1.15 × 10−4) = 2.20/(1.106 × 10−11) = 2.0 × 1011 Pa.
Worked example 2. The diameter is measured as 0.40 ± 0.01 mm, the length as 2.00 ± 0.01 m, and the gradient has an uncertainty of 4%. Estimate the percentage uncertainty in E.
Diameter: 0.01/0.40 = 2.5%, doubled for the area: 5.0%.
Length: 0.01/2.00 = 0.5%.
1 / 2Next ▶
Worked examples
Worked examples
Gradient: 4%.
Total ≈ 5.0 + 0.5 + 4 = 9.5%, about 10%. The diameter dominates.
Worked example 3. A wire of E = 2.0 × 1011 Pa, length 1.5 m and diameter 0.50 mm carries a load of 20 N. Predict the extension.
A = π(0.50 × 10−3)2/4 = 1.96 × 10−7 m2.
Δx = FL/(AE) = (20 × 1.5)/(1.96 × 10−7 × 2.0 × 1011) = 30/(3.93 × 104) = 7.6 × 10−4 m = 0.76 mm.
◀ Previous2 / 2
Key terms
Term Meaning
Young modulus Stress divided by strain in the elastic region (Pa).
Micrometer screw gauge Instrument reading to 0.01 mm used for wire diameters.
Reference wire A second identical wire used to compensate for temperature and support movement.
Limit of proportionality Maximum force for which extension remains proportional to force.
Percentage uncertainty Absolute uncertainty divided by the measured value, times 100.
1Avoid these mistakes2Avoid these mistakes
Avoid these mistakes
1Avoid this
Measuring the diameter only once or only in one direction; the wire may not be uniform or circular.Avoid this
2Avoid this
Using the whole length of the wire (including the part around the pulley) instead of the length from clamp to marker.Avoid this
3Avoid this
Exceeding the elastic limit, so the graph is not a straight line and E is underestimated.Avoid this
1 / 2Next ▶
Avoid these mistakes
4Avoid this
Forgetting to square the percentage uncertainty contribution (doubling) when the diameter appears as dAvoid this
.Avoid this
5Avoid this
Reading the gradient of Δx against F and quoting it as E without applying E = L/(A × gradient).Avoid this
◀ Previous2 / 2
Accepted payment methods