Curriculum
Course: Edexcel IAL Physics (IAS & A2)
Login

Curriculum

Edexcel IAL Physics (IAS & A2)

1. Mechanics and Materials

0/71 Dr Dabour Hub Science Diagram and Course Material

2. Waves and Electricity

0/108 Dr Dabour Hub Science Diagram and Course Material

3. Practical Skills in Physics I

0/52 Dr Dabour Hub Science Diagram and Course Material

4. Further Mechanics, Fields and Particles

0/90 Dr Dabour Hub Science Diagram and Course Material

5. Thermodynamics, Radiation, Oscillations and Cosmology

0/96 Dr Dabour Hub Science Diagram and Course Material
Text lesson

1.6.3 Force-Extension Graphs

1.6.3 Force-Extension Graphs — EDEXCEL IAL PHYSICS (IAS & A2) notes: Interpret force–extension graphs, including Hooke’s law, elastic and plastic behaviour and the yield point.

1Hooke’s law2Equation3Stiffness · Compression
Hooke’s law
Hooke’s law
the extension of a material is directly proportional to the applied force up to the limit of proportionality.
1 / 3Next ▶
Equation
1

F = kx.What the symbols mean: F = force (N) · k = spring constant (N m−1) · x or e = extension (m)
2

F is the applied force (N).
3

k is the spring constant (N m-1), a measure of stiffness.
4

x is the extension (m).
◀ Previous2 / 3Next ▶
Stiffness · Compression
Stiffness
the larger the spring constant, the stiffer the material.
Compression
Hooke’s law applies to compressions as well as extensions.
◀ Previous3 / 3
1Straight line · Gradient · Curve2Swapped axes
Straight line · Gradient · Curve
Straight line
the graph is a straight line through the origin while the material obeys Hooke’s law.
Gradient
the gradient of the straight section equals the spring constant k.
Curve
as more force is added the line may start to curve.
1 / 2Next ▶
Force-extension graph: straight line through the origin up to the limit of proportionality (0.050 m, 10 N), curve bending to the elastic limit (0.100 m, 15 N), dashed unloading line to a permanent extension of about 0.025 m.
Swapped axes
Force-extension graph: straight line through the origin up to the limit of proportionality (0.050 m, 10 N), curve bending to the elastic limit (0.100 m, 15 N), dashed unloading line to a permanent extension of about 0.025 m." loading= - Dr Khaled Dabour Academy⤢ Enlarge
Swapped axes
if extension is on the y-axis, the gradient is 1/k

so k = 1/gradient.
◀ Previous2 / 2
1Limit of proportionality2Elastic limit
Limit of proportionality
1

the point beyond which Hooke’s law no longer holds.
2

It is where the line starts to curve.
1 / 2Next ▶
Force against extension graph with a straight line through the origin that curves after the limit of proportionality
Elastic limit
Force against extension graph with a straight line through the origin that curves after the limit of proportionality" loading= - Dr Khaled Dabour Academy⤢ Enlarge
Elastic limit
the point before which a material returns to its original length when the force is removed.
It always comes after the limit of proportionality.
◀ Previous2 / 2
1Yield point · Elastic deformation · Plastic deformation2Unloading
Yield point · Elastic deformation · Plastic deformation
Yield point
the point where the material continues to stretch even though no extra force is applied.
It occurs well past the elastic limit.
Elastic deformation
the material returns to its original shape when the load is removed.
Plastic deformation
beyond the yield point the material does not return to its original shape when the load is removed.
1 / 2Next ▶
Unloading
Unloading
from the plastic region the graph returns along a line parallel to the original straight section, ending at a permanent extension.
◀ Previous2 / 2
Same shape · Unique to each material · Not identical
Same shape
compression can be written as a negative extension but the graphs have the same shape

compression is plotted as a positive value.
Unique to each material
each material has its own graph depending on how brittle or ductile it is.
Not identical
a force–compression graph differs from the force–extension graph because materials behave differently in tension and compression.
Other materials
1

Rubber band the graph is a curve, not a straight line.
2

Loading and unloading follow different paths (hysteresis).
3

The area between the curves is energy transferred to thermal energy.
4

Rubber returns to its original length but does not obey Hooke’s law.
5

Polythene strip stretches easily and shows a large permanent extension.
6

Brittle materials such as glass, follow a straight line to fracture with little plastic region.
1Series · Parallel2Area under the graph
Series · Parallel
Series
both springs carry the same force and the extensions add.
1/k = 1/k1 + 1/k2

which is softer than either spring.
Parallel
the extension is the same and the forces add.
k = k1 + k2

which is stiffer.
1 / 2Next ▶
Area under the graph
Area under the graph
the area under a force–extension graph is the work done in stretching.
Elastic potential energy is energy held in a material, such as a spring, after it has been stretched or squashed.
While a material still obeys Hooke’s law, the work done stretching it is stored as elastic strain energy.
A wire under stress that suddenly breaks is dangerous

because its stored elastic energy converts into kinetic energy.
◀ Previous2 / 2
More from the specification
Tensile Stress, Tensile Strain, and Young Modulus
  • Tensile stress σ is defined as applied force per unit cross-sectional area,
    • (σ = F / A, in pascals, Pa)
  • while tensile strain ε is the fractional change in length; the Young modulus E is the ratio of tensile stress to tensile strain within the limit of proportionality: E = σ / ε = (F·L₀) / (A·ΔL).
    • (ε = ΔL / L₀, dimensionless)
Interpreting Stress-Strain Graphs and Material Properties
  • On a stress-strain graph, the initial linear gradient represents the Young modulus; the limit of proportionality, elastic limit,
  • and yield point indicate the onset of plastic deformation, culminating at the ultimate tensile strength and final breaking stress where fracture occurs.
Strain Energy and Toughness from Area Under Curves
  • The area under a force-extension curve represents the elastic strain energy stored or work done in deforming a material; on a stress-strain curve, the total area under the curve represents the energy absorbed per unit volume (material toughness) up to the breaking point.
    • (estimated by counting squares)
Stress
  • Force per unit cross-sectional area, σ = F/A.
    What the symbols mean: σ = stress (Pa) · F = tensile force (N) · A = cross-sectional area (m2)
Strain
  • Extension per unit original length, ε = x/L.
Young modulus
  • Ratio of stress to strain for a material, E = σ/ε.
Breaking stress
  • The stress at the point where the material fractures.
Key terms
Term Meaning
Hooke’s law Extension is proportional to force up to the limit of proportionality.
Spring constant The force per unit extension, k (N m-1).
Limit of proportionality The point beyond which extension is no longer proportional to force.
Elastic limit The point before which the material returns to its original length.
Yield point The point where the material stretches with no extra force.
Plastic deformation A permanent change in shape after the force is removed.
1Avoid these mistakes2Avoid these mistakes
Avoid these mistakes
1Avoid this
Using the total length instead of the extension in F = kxx is the increase in length.
2Avoid this
Assuming the elastic limit and the limit of proportionality are always the same pointthe elastic limit comes after.
3Avoid this
Reading the gradient as k when the axes are swappedthen the gradient is 1/k.
1 / 2Next ▶
Avoid these mistakes
4Avoid this
Saying rubber obeys Hooke’s law because it is elasticits graph is not linear.
◀ Previous2 / 2
Accepted payment methods