Curriculum
Course: Edexcel IAL Physics (IAS & A2)
Login

Curriculum

Edexcel IAL Physics (IAS & A2)

1. Mechanics and Materials

0/71 Dr Dabour Hub Science Diagram and Course Material

2. Waves and Electricity

0/108 Dr Dabour Hub Science Diagram and Course Material

3. Practical Skills in Physics I

0/52 Dr Dabour Hub Science Diagram and Course Material

4. Further Mechanics, Fields and Particles

0/90 Dr Dabour Hub Science Diagram and Course Material

5. Thermodynamics, Radiation, Oscillations and Cosmology

0/96 Dr Dabour Hub Science Diagram and Course Material
Text lesson

3.2.3 Significant Figures

3.2.3 Significant Figures — EDEXCEL IAL PHYSICS (IAS & A2) notes: Count significant figures, round correctly and record data and results to an appropriate precision.

Significant figures · Use · Exam marks
Significant figures
the digits in a number that are reliable and necessary to indicate the quantity.
Use
significant figures must be used when dealing with quantitative data.
Exam marks
a question may state the number of significant figures required, and a mark is often given for it.
Counting significant figures: Counting significant figures from the first nonzero digit: 1267 m has four, and 55.0 g has three because the zero after the decimal point was measured.
Rules for counting
Rule Examples
All non-zero digits are significant 4107 has 4 s.f.
Zeros between non-zero digits are significant 29.009 has 5 s.f.
Zeros before all non-zero digits are not significant 0.00079 has 2 s.f.; 0.48 has 2 s.f.
Trailing zeros in a number without a decimal point are not significant 57,000 has 2 s.f.; 640 has 2 s.f.
Zeros after non-zero digits within a number with decimals are significant 689.0023 has 7 s.f.
1Rounding2Rounding
Rounding
Rounding
1
Identify the significant figures using the rules.
2
Count from the first significant figure to the required number.
3
Look at the next digit (the decider).
1 / 2Next ▶
Rounding
Rounding
4
If the decider is 5 or greater, increase the last kept digit by 1.
Intermediate steps

do not round intermediate values until the final answer.
◀ Previous2 / 2
1Resolution · Trailing zeros · Micrometer2Typical
Resolution · Trailing zeros · Micrometer
Resolution
record each reading to the resolution of the instrument, with a consistent number of decimal places.
Trailing zeros
keep them if the display shows them.

(2.40 V, not 2.4 V)
Micrometer
readings are quoted to 3 significant figures, e.g. 2.30 mm.
1 / 2Next ▶
Typical
Typical
3 significant figures is usual for data that will be plotted.
◀ Previous2 / 2
1Multiplying or dividing · Adding or subtracting · Column con2Means
Multiplying or dividing · Adding or subtracting · Column consistency
Multiplying or dividing
no more significant figures than the least precise input.
Adding or subtracting
the same number of decimal places as the least precise input.
Column consistency
all values in a column have the same number of significant figures.
1 / 2Next ▶
Means
Means
it is acceptable to give a mean to one more significant figure than the readings.
◀ Previous2 / 2
Uncertainty · Gradients · Standard form
Uncertainty
quote to one significant figure

then match the value to the same decimal place.(two if it starts with 1)
Gradients
two or three significant figures are usually appropriate.
Standard form
writing 2.50 × 102 m makes the number of significant figures clear.
1Precision limits on instrument scale
  • Precision limits on instrument scale recording experimental quantities to consistent significant figures reflects the smallest graduation interval on the measuring scale.
2Significant Figures Convention
  • In experimental physics, calculated quantities should be quoted to the same number of significant figures as the raw measurement with the least precision.
3Timing Oscillations with Fiducial Markers
  • In a mass-spring or pendulum experiment, timing 10 or 20 complete oscillations past a central fiducial marker minimizes human reaction time error in the measured period.
4Identifying and Discarding Anomalies
  • Repeated measurements taken over an experimental range must be inspected for anomalous values before calculating a representative mean.
5Appropriate Choice of Measuring Instruments
  • Measuring length or extension using a metre ruler provides millimetre resolution (± 1 mm),
  • whereas a micrometer screw gauge is needed for wire diameter (± 0.01 mm).
6Significant Figures Convention
  • In experimental physics, calculated quantities should be quoted to the same number of significant figures as the raw measurement with the least precision.
7Timing Oscillations with Fiducial Markers
  • In a mass-spring or pendulum experiment, timing 10 or 20 complete oscillations past a central fiducial marker minimizes human reaction time error in the measured period.
8Identifying and Discarding Anomalies
  • Repeated measurements taken over an experimental range must be inspected for anomalous values before calculating a representative mean.
9Appropriate Choice of Measuring Instruments
  • Measuring length or extension using a metre ruler provides millimetre resolution (± 1 mm),
  • whereas a micrometer screw gauge is needed for wire diameter (± 0.01 mm).
10Fiducial marker alignment
  • Fiducial marker alignment placing a fiducial marker at equilibrium marks the period of oscillations accurately when measuring elapsed time.
11Experimental range and intervals
  • Experimental range and intervals planning measurements across an extended range with uniform intervals reveals genuine trends in experimental results.
12Timing multiple periods
  • Timing multiple periods timing ten oscillations on a stopwatch minimizes timing errors before calculating the single period.
13Apparatus
  • The equipment needed to carry out an experiment.
14Extension
  • Increase in length over the original length.
15Anomalous reading
  • A measurement that does not fit the pattern of the other data.
16Fiducial marker
  • A fixed reference mark used to judge when an oscillating object passes its centre position.
17Potential difference
  • Work done by a unit charge passing through a component.
18Elastic limit
  • Greatest load a spring can recover from.
19Anomalous result
  • A result that does not fit the trend of the other data.
20Oscillation
  • Repeated back-and-forth motion.
21Period
  • Time for one revolution.
22Error
  • The difference between a measurement and the true value.
23Current
  • Flow of electrons in a circuit.
24Pendulum
  • A weight swinging on a string, exchanging GPE and KE.
Key terms
Term Meaning
Significant figure A digit that contributes to the precision of a number.
Decimal place A digit to the right of the decimal point.
Standard form A number written as a × 10n.
Rounding Reducing the number of digits and adjusting the last one kept.
Precision Closeness of repeated measurements, shown by the figures recorded.
1Avoid these mistakes2Avoid these mistakes
Avoid these mistakes
1Avoid this
Writing a calculator display such as 12.32142857 as the answer.Avoid this
2Avoid this
Dropping trailing zeros from a readingwrite 2.40 when the display shows 2.40.
3Avoid this
Giving an uncertainty to more places than the value, or the value to more places than the uncertainty allows.Avoid this
1 / 2Next ▶
Avoid these mistakes
4Avoid this
Rounding in the middle of a multi-step calculation.Avoid this
◀ Previous2 / 2
Accepted payment methods